User manual AT&T 2230

[. . . ] This product can provide information only if both you and the caller are in areas offering Caller ID service, and if both telephone companies use compatible equipment. About Call History This phone assigns each incoming call a number from 1 to 25. When the memory is full, the oldest call information is deleted to make room for new incoming call information. If you answer a call before call information appears on the screen, it will not be in the call history. 1 INSTALLATION Base Installation NOTE: Install the base unit and spare handset charger away from electronic equipment, such as personal computers, television sets or microwave ovens. 1 Connect the power cord to the base and an electrical outlet not controlled by a wall switch. Modular telephone jack Standard electrical outlet 2 Connect the telephone line cord. [. . . ] 2 Press < until the screen displays >LANGUAGE CLEAR MSG WAIT 3 Press S. The screen displays >LANGUAGE ENGLISH 4 5 Press < or > to select a language. Press S to save the displayed setting. Clear Message Waiting If you subscribe to telephone company voice mail, and the message waiting indicator remains on even after you have reviewed all messages, follow the directions below to turn off the indicator. NOTE: These steps will clear the message waiting indicator for BOTH handsets. Press < until the screen displays >CLEAR MSG WAIT DIAL METHOD 3 Press S. The screen displays CLEAR MSG WAIT CONFIRM? 4 Press S to confirm -- OR -- Press to exit without clearing. 8 FEATURE SETUP Set Dial Mode NOTE: When you change the dial mode setting, BOTH handsets are affected. 2 Press < until the screen displays >DIAL METHOD CALL LOG 3 Press S. The screen displays >DIAL METHOD DTMF 4 5 Press < or > to display DTMF or PULSE. Press S to save displayed setting. 9 TELEPHONE OPERATION Call Timer The screen displays a timer and whether the call is external or internal (intercom). Flash/Call Waiting 1 Press F to connect to the new call when you receive a call-waiting signal. NOTE: Use F to access other phone company subscriber services, as described by your provider. Making a Call 1 Press P, then dial the number -- OR -- Dial the number, then press P. 2 Press P again to end the call. Answering a Call 1 Press P to answer a call. NOTE: If you have the Auto Answer feature turned on, you can answer a call by lifting the handset from the Intercom 1 Signal one handset from the other by pressing I. 2 To answer, press P on the second handset. Redial 1 Press R before pressing P to call the last number (up to 24 digits) dialed from either handset. 2 Press P to end the call. base or charger. 10 TELEPHONE OPERATION Page/Handset Locator Page the handsets from the base by pressing L. Storing a number and name in one handset automatically stores it in both. Storing a Number and Name in Phone Book 1 2 Press S. Press < until the screen displays >PHONEBOOK HANDSET VOLUME 3 4 Press S. Begin at Step 4 to enter another telephone number and name -- OR -- Press to exit. Dial Key 1 2 3 4 5 6 7 8 9 0 * # 1 space A D G J M P T W 0 2 1 B E H K N Q U X ?b e h k n p u w ) & c f i l o q v x 8 9 r y s z * # 13 TELEPHONE PHONE BOOK Dialing a Number in Phone Book 1 2 Press m. Enter the first letter of the stored name, then scroll using < or > -- OR -- Press < or > to scroll through memory locations. Press P to dial the displayed number. 3 Editing a Number/Name in Phone Book 1 2 3 Press m. Press to erase a digit -- OR -- Press and hold to delete entire telephone number. Press to erase a character -- OR -- Press and hold to delete entire name. [. . . ] You might have too many extension phones on your telephone line to allow all of them to ring. If you have dial pulse (rotary) service, you'll need to set the dial mode to PULSE. Follow the instructions under "Set Dial Mode" in the FEATURE SETUP section of this manual. If you have touch tone service and you hear clicks while you are dialing, you'll need to set the dial mode to DTMF. [. . . ]