User manual AXIS SHDUG

[. . . ] AXIS StorPoint NAS 100 User's Guide Read Me First 1 Read Me First This guide applies to the AXIS StorPoint NAS 100 network hard disk server with firmware release 1. 00 and subsequent releases until otherwise notified. It is intended for anyone involved in installing and using the StorPoint NAS. It includes the most basic instructions on how to get your StorPoint NAS up and running. For a more detailed description of the StorPoint NAS 100 and its functionality, refer to the "AXIS StorPoint NAS 100 User's Manual" which is available in PDF format at the Axis Web Site and on the AXIS Online CD. [. . . ] · If you do not have TCP/IP, you must use a text editor and edit the configuration file manually. Notes: · When installing the first StorPoint NAS into the NDS tree, it is recommended that you use an account with Supervisor rights to the [Root] of the tree. This means that the user specified in the NDS Admin Name parameter must have Supervisor access rights. · The StorPoint NAS will extend the NDS Schema with a new attribute called AXIS:SPcd:rights which will be added to the NDS Server object class. The extension is needed for storing configuration data and has been approved by Novell. · If you do not have Supervisor rights to [Root] or if schema extensions are not allowed in your NDS tree, you can store the access rights in a file on a Novell file server. However, you must specify the NDS Rights Storage and NDS Rights File parameters properly. After the NDS installation, you must also create and assign access rights to the directory on the Novell file server where the file is stored. Synchronizing the NDS Tree Before installing the StorPoint NAS in the NDS tree you need to verify that the NDS tree is synchronized. To do that, load DSREPAIR on the server in the NDS tree and select Unattended full repair. Important! If the NDS tree is not synchronized, do not continue the installation until you have solved the problem. 18 Setup for NetWare (NCP) Using the Installation Wizard 1. Verify that the NDS tree is synchronized. AXIS StorPoint NAS 100 User's Guide 2. To verify that the StorPoint NAS was successfully installed, check the Event Log for errors. Use a standard text editor such as Notepad to edit the configuration parameters. From Windows Explorer or File Manager, locate the StorPoint NAS configuration file config. ini file which is located in the System/ServerProperties folder. In NetWare, the default name of your StorPoint NAS is AXIS<nnnnnn>_NW where <nnnnnn> are the last six digits of the StorPoint NAS serial number. AXIS StorPoint NAS 100 User's Guide Setup for NetWare (NCP) 19 3. Enter the appropriate settings for the following parameters: Parameter name TimeZone TimeSyncSource NDSEnable NDSTreeName NDSServerContext NDSAdminName Value = = NDS = yes = = = Description Must be set to the correct time zone that the StorPoint NAS is operating in. Set to NDS to enable the StorPoint NAS to get its time from the NetWare network. Specify the name of the tree where you want to install the StorPoint NAS, e. g. MEDCORP Specify the distinguished name of the context in the NDS tree where you want to install the StorPoint NAS, e. g. Manufacturing. Medtec Specify the distinguished name of a user or administrator with Supervisor or Create rights to the context where you want to install the StorPoint NAS, e. g. Admin. Medtec Specify the password of the administrator entered in NDSAdminName shown above. Once written, this password will appear as ******. NDSAdminPassword = NDSInstall NDSRightsStorage = install Change this to install when you are ready to install the StorPoint NAS. [. . . ] Enter the name or IP address of the StorPoint NAS in the location/address field. Select the Automatically fix file system errors checkbox to fix the errors automatically. Click Start to start checking for errors. Note: If you do not select the Automatically fix file system errors checkbox, only a hard disk check will be performed. All results can be viewed in the Event Log. 32 Raid 1 (Mirroring) AXIS StorPoint NAS 100 User's Guide Raid 1 (Mirroring) The StorPoint NAS has a built-in RAID 1 option. [. . . ]