User manual BARRACUDA NG FIREWALL QUICK CONFIGURATION GUIDE

[. . . ] There are only a few manual steps required to activate this. Transparent HTTP Proxy All models with pre-configured WiFi will also include a pre-configured http caching proxy operating in transparent mode. DHCP Server For appliances F101, F201, F301 with included WiFi a DHCP service is pre-configured to dynamically assign IP addresses from the pool between 192. 168. 201. 1 to 192. 168. 201. 16. WiFi For appliances F101, F201, F301 with included WiFi hardware and antenna a corresponding WiFi service is pre-configured. For security reasons, this is not activated by default and requires a few manual steps to activate. Import License (recommended) Barracuda NG Firewalls provide firewall, VPN and L7AP functionality in DEMO MODE to be used for evaluation and training purposes without a license, but this includes severe restrictions concerning security. The default root password of ngf1r3wall will always work and no access control lists (ACL) from where remote login is permissible can be set up. [. . . ] Click Trust Key to continue The next screen displayed is the Simple config screen. In the section Operational Configuration under Firewall click on the Ruleset link. Make sure the Forwarding ruleset is selected by clicking on the Forwarding Rules button on the left. 2 NG Firewall Barracuda NG Firewall - Quick Configuration Guide Forwarding Rule Configuration To the right of the rule set screen the currently active firewall rule set is displayed. Please note that by default the BLOCKALL rule is on first place on top blocking all traffic. Note: Depending on the model of Barracuda NG Firewall there might be more rules displayed. If this rule is not strict enough modify the rule according to your needs. For a detailed description on how to modify firewall rules please have a look to the Administrator's Guide. Residing on the USB thumb drive delivered with your Barracuda NG Firewall appliance and is also available for download at www. barracudanetworks. com in the Barracuda NG Firewall product section. . Continue with any other firewall rule specifying access to the internet. Enable Layer 7 Application Profiling Click Application/IPS in the Views section on the left side of the rule window. If needed set Application Detection to Limit Bandwidth or Drop Traffic. Under Explicit Application Selection review, and if necessary, modify the protocols. The Protocols column represents all available protocols, the Selected Protocols column represents the currently selected ones that will be detected. When done click OK. Commit Changes To commit all previously done configuration steps, the new configuration needs to be activated at the Barracuda NG Firewall. Click Send Changes followed by Activate. 3 NG Firewall Barracuda NG Firewall - Quick Configuration Guide WiFi Enable WiFi Commit Changes To commit all previously done configuration steps, the new configuration needs to be activated at the Barracuda NG Firewall. Click Send Changes followed by Activate. Open the Simple Config screen and open the Network link within the Device Configuration section. This will open the network configuration window. Select a Channel appropriate to your country Select a Transmission Power level Note: As model F101 has no active cooling fan, the highest Transmission Power is only recommended, if the appliance is located in a cool and well ventilated location. 4 NG Firewall Barracuda NG Firewall - Quick Configuration Guide WiFi Configuration Select Config from the tab selection menu and switch to Full Config by clicking the Full Config button. [. . . ] Click Send Changes followed by Activate. In the upcoming tree structure navigate to HTTP: Virtual Servers > S1 EXPORT > Assigned Services > HTTP and open the configuration node by double clicking it. Double click on Service Properties. Close the configuration window by clicking . To enable modification of settings, click the Lock button in the upper-right area of the User Interface. 9 NG Firewall Barracuda NG Firewall - Quick Configuration Guide DHCP Server Enable DHCP Service Select Config from the tab selection menu and switch to Full Config by clicking the Full Config button. Commit Changes To commit all previously done configuration steps, the new configuration needs to be activated at the Barracuda NG Firewall. Click Send Changes followed by Activate. In the upcoming tree structure navigate to DHCP(DHCP Service): Virtual Servers > S1 EXPORT > Assigned Services > DHCP(DHCP Service) and open the configuration node by double clicking it. [. . . ]