User manual BINATONE IDECT V2I SYSTEM
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BINATONE IDECT V2I SYSTEM. We hope that this BINATONE IDECT V2I SYSTEM user guide will be useful to you.
Manual abstract: user guide BINATONE IDECT V2I SYSTEM
Detailed instructions for use are in the User's Guide.
[. . . ] iDect_V2i_IFU_master. book Page 1
Thursday, March 27, 2008
2:54 PM
USER GUIDE
iDECT V2i System
DIGITAL CORDLESS TELEPHONE & ANSWERING MACHINE
THIS EQUIPMENT IS NOT DESIGNED FOR MAKING EMERGENCY TELEPHONE CALLS WHEN THE POWER FAILS. ALTERNATIVE ARRANGEMENTS SHOULD BE MADE FOR ACCESS TO DIAL EMERGENCY SERVICES.
Ver. 4, Feb 08 (BTP)
Before operating this set, please read these instructions carefully.
iDect_V2i_IFU_master. book
Page 1
Thursday, March 27, 2008
2:54 PM
Important note -- emergency calls
The iDECT V2i is not designed for making emergency calls if the mains power fails. So you should make alternative arrangements for access to Emergency Services. [. . . ] It will play a predefined message and will allow the caller to leave a message if they desire, of up to 2 minutes per message. The total recording time available for all messages is about 12 minutes. There are a number of settings that can be adjusted to personalise the telephone's operation to suit your needs. The telephone answering modes
The telephone has two answering modes, Answer Only mode and Answ. mode is switched on by default and will remain on unless you change mode.
To change answering mode:
1
M u M d M
Press the MENU/OK button ONCE then the U button ONCE !Press the U or D buttons to select the new mode and then MENU/OK to confirm !> Predefined Turn to page 30 to set up the outgoing message
2
3 4
:
M
5
Help Line: 0845 345 9677 (Local Call rate)
29
iDect_V2i_IFU_master. book
Page 30
Thursday, March 27, 2008
2:54 PM
Answering machine setup
The outgoing message
The telephone is supplied with two predefined outgoing messages (OGM). One is for use in Answer Only mode and one for use in Answer & Record mode. Both of these can be replaced with your own prerecorded message if you prefer. To pre-record an outgoing message you must first follow the procedure to set the answer mode
To record a new outgoing message:
After setting the answer mode you can choose between using a predefined outgoing message or using a personalised one that you have recorded. If you select Personalised you will then need to record a new message.
1 2
Follow steps 1 to 5 on page 29 !> Predefined
d M M d M M
Press the D button to select Personalised and press the MENU/OK button !Display shows > Play message Press the MENU/OK button to play the existing message Press the D button and the MENU/OK button to record a new message !Speak clearly into the handset Press the MENU/OK button to end the recording. > Personalised If you are not happy with the result, repeat from step 2.
3 4
5 6
7
M
30
iDect_V2i_IFU_master. book
Page 31
Thursday, March 27, 2008
2:54 PM
Answering machine setup
8
B
Use the BACK button to exit the menu or press the HANG UP button to return to standby mode.
Setting the ring delay
You can adjust the number of rings that sound before the machine answers the call:
1
M u M d M M
Press the MENU/OK button ONCE then the U button ONCE !Display shows Ring Delay > 5 rings Use the U or D buttons to adjust the ring delay between 3 and 8 rings or Toll Saver If you select Toll Saver the telephone will answer after 2 rings, if there are new messages on the answering machine, but after 5 rings if there are no new messages. This allows you to call from a remote telephone to check your messages, and if it does not answer after 3 rings, you know there are no new messages, so you can hang up without being charged for the call.
2
3 4 5
:
6 7
M B f
Press the MENU/OK button to confirm the new setting Use the BACK button to exit the menu or press HANG UP to go to standby mode
Help Line: 0845 345 9677 (Local Call rate)
31
iDect_V2i_IFU_master. book
Page 32
Thursday, March 27, 2008
2:54 PM
Answering machine setup
Call Screening
The call screening function allows you to listen to incoming messages as they are recorded so you can decide if you would like to take the call. The telephone is supplied with call screening switched on, but you can switch it off if you want. When call screening is switched on, handset 1 loudspeaker will turn on automatically while the answering machine is recording an incoming message.
To switch call 1 screening on or off:
M u
Press the MENU/OK button ONCE then the U button ONCE !Display shows HS Screening > Off (or On) Press the U or D button to select Off or On Press the MENU/OK button to confirm the change Use the BACK button to exit the menu or press HANG UP to go to standby mode
2
M u 3M d
4 5 6 7
M u M B f
32
iDect_V2i_IFU_master. book
Page 33
Thursday, March 27, 2008
2:54 PM
Answering machine operation
When the answering machine is switched on the TAM icon on the handset display will come on steadily. When the answering machine is recording a message the handset will display ICM Recording. The TAM icon flashes when the recording ends, to indicate a new message. [. . . ] Network connection This equipment is intended to be used in the UK only. Operation on other countries' PSTN termination points cannot be guaranteed.
Binatone Telecom plc operates a policy of continuous product improvement, and so reserves the right to make changes to the product and functions without notice.
Help Line: 0845 345 9677 (Local Call rate)
55
iDect_V2i_IFU_master. book
Page 56
Thursday, March 27, 2008
2:54 PM
Registering new handsets
The handset(s) supplied with your iDECT V2i base unit are already registered to it, so you don't need to register them. But if you've bought extra handsets separately, you'll need to register them. To register a new handset
Make sure the handset you're registering is in standby mode.
1 2 3
M d M d M
Press the MENU/OK button ! [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BINATONE IDECT V2I SYSTEM
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BINATONE IDECT V2I SYSTEM will begin.