User manual BINATONE IDECT X2I TWIN
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BINATONE IDECT X2I TWIN. We hope that this BINATONE IDECT X2I TWIN user guide will be useful to you.
Manual abstract: user guide BINATONE IDECT X2I TWIN
Detailed instructions for use are in the User's Guide.
[. . . ] Your guarantee All of our technology products are guaranteed for 2 years, 5 years for televisions. Please retain your Marks & Spencer till receipt which is proof of purchase, and will validate the date from which your guarantee will run. Please also retain the original packaging in case you need to return the product. In the unlikely event of a fault please call our technology customer service centre on 0845 671 0665. [. . . ] To answer the outside call and end the intercom call: Press the PHONE button briefly OR, to answer the outside call and put the intercom call on hold (so you can later use shuttle, conference or transfer): Press the INT/# button for one second If you now want to set up a three-way conference, simply press and hold the INT/# button for one second.
To page all handsets from the base unit
To make all registered handsets ring (this is useful if you've forgotten where you put a handset):
1
Press the HANDSET LOCATOR button on the base unit è The handsets ring for up to 20 seconds and their displays show <Paging>. To stop the ringing before 20 seconds: EITHER press the HANDSET LOCATOR button again OR press any button on any handset.
28
Answering machine setup
Answering machine setup
The telephone is supplied with the answering machine switched on and set up to automatically answer a call after five rings. It will play a predefined message and will allow the caller to leave a message if they desire. There are a number of settings that can be adjusted to personalise the telephone's operation to suit your needs. The telephone The telephone has two answering modes, Answer Only mode and Answ& Rec. mode is switched on by default and will remain on unless you change mode. To change answering mode:
1
Press the MENU/OK button ONCE then the á button ONCE
è Display Shows
Main Menu >Answ Machine
2
Press the MENU/OK button once then the â button THREE times è Display Shows Answ. Mode >Answ.
& Rec.
3 4
Press the á â buttons to select the new mode and then MENU/OK to confirm è Display Shows Select mess >Predefined Turn to page 30 to set up the outgoing message
5
Help Line: 0845 671 0665 (Local Call rate)
29
Answering machine setup
The outgoing message
The telephone is supplied with two predefined outgoing messages (OGM). One is for use in ANSWER ONLY mode and one for use in Answer & Rec. mode. Both of these can be replaced with your own prerecorded message if you prefer. To pre-record an outgoing message you must first follow the procedure to set the answer mode After setting the answer mode you can choose between using a predefined outgoing message or using a personalised one that you have recorded. If you select Personalised you will then need to record a new message.
To record a new outgoing message:
1 2
Follow steps 1 to 5 on page 29 è Display Shows Select mess >Predefined Press the â button to select Personalised and press the MENU/OK button è Display shows >Play message Press the MENU/OK button to play the existing message Press the â button and the MENU/OK button to record a new message è Display Shows > Record mess Speak clearly into the handset Press the MENU/OK button to end the recording. è Display Shows Select mess>Personalised If you are not happy with the result, repeat steps 2. Use the CANCEL button to exit the menu
3 4
5 6
7
8 30
Answering machine setup
Setting the ring delay
You can adjust the number of rings that sound before the machine answers the call:
1
Press the MENU/OK button ONCE then the á button ONCE è Display Shows Main Menu >Ans Machine Press the MENU/OK button ONCE then the â button FIVE times è Display Shows Ans Machine >Settings Press the MENU/OK button è Display Shows Settings >Ring Press the MENU/OK button è Display Shows Ring Delay >5
Delay
2
3 4 5
rings
Use the á â buttons to adjust the ring delay between 3 and 8 rings or Toll Saver If you select Toll Saver the telephone will answer after 3 rings, if there are new messages on the answering machine, but after 5 rings if there are no new messages. This allows you to call from a remote telephone to check your messages, and if it does not answer after 3 rings, you know there are new messages, so you can hang up without being charged for the call.
6 7
Press the MENU/OK button to confirm the new setting Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode
Help Line: 0845 671 0665 (Local Call rate)
31
Answering machine setup
Call Screening
The call screening function allows you to listen to incoming messages as they are recorded so you can decide if you would like to take the call. When call screening is switched on using the menu below, if the handset displays. "'ICM Recording'. Press the MENU/OK button ONCE then the á button ONCE è Display Shows Main Menu >Ans Machine Press the MENU/OK button ONCE then the â button FIVE times è Display Shows Ans Machine >Settings Press the MENU/OK button ONCE then the â button TWICE è Display shows Settings >HS Screening Press the MENU/OK button è Display Shows HS Screening Press the á button è Display Shows HS Screening
>Off
To switch call 1 screening on:
2
3
4 5 6 7
>On
Press the MENU/OK button to confirm the change Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode
32
Answering machine operation
Answering machine operation
18:44 12/08
JANE
1
n
When the answering machine is switched on the TAM icon on the handset display will come on steadily. When the answering machine is recording a message the handset will display ICM recording. If call screening is on the SPK icon will come on and the incoming message can be heard on the speaker
18:44 12/08
n
handset #
ICM Recording
18:44 12/08
n
handset
#
ICM Recording
To stop the recording and take the call, simply press the PHONE button in the normal way, if call screening is on, you need to press HANG UP button to turn off call screening mode, then press the PHONE button in the normal way. Turn the 1 answering machine on or off: Press the MENU/OK button ONCE then the á button ONCE è Display Shows Main Menu >Ans Machine Press the MENU/OK button ONCE then the á button TWICE. è Display Shows Ans Machine >Answer On/Off Press the MENU/OK button è Display Shows Answer On/Off
>On
2
3 4 5
Press the âor button to select Off or On and then the MENU/OK button to confirm Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode
Help Line: 0845 671 0665 (Local Call rate)
â
33
Answering machine operation
Message Playback
The telephone can store a number of message in its memory. The messages will be available for replay until you delete them to make room for new messages.
n
18:44 12/08
New messages that have not yet been played are indicated by the TAM icon flashing . [. . . ] Remember to include the mains adapter 3 Call our Service Department on 0845 671 0665 and ask for details of where to send your telephone for repair. 4 Make sure you include with your telephone: your name and address A copy of your sales invoice. 5 Return your telephone to the address given by the Service Department
54
Color profile: Disabled Composite Default screen
Technical details
Standard Frequency range Digital Enhanced Cordless Telecommunications (DECT) 1. 88 to 1. 9 GHz (bandwidth = 20 MHz)
Channel bandwidth 1. 728 MHz Operating range Operating time up to 300 m outdoors; up to 50 m indoors standby: 100 hours approx. battery charge time: 1215 hours
Temperature range Operating 0 ºC to 40 ºC Storage -20 ºC to 60 ºC Electrical power Handset -- 450mA Li-ion rechargeable battery Pack
Base unit -- 7. 5V DC 300mA Charger pod -- 9V AC 300mA
Port specification The DC 7. 5 port (connected to the mains power supply) is a SELV port with respect to EN41003. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BINATONE IDECT X2I TWIN
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BINATONE IDECT X2I TWIN will begin.