User manual BOSS BV9995B
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSS BV9995B. We hope that this BOSS BV9995B user guide will be useful to you.
Manual abstract: user guide BOSS BV9995B
Detailed instructions for use are in the User's Guide.
[. . . ] If you must replace a fuse in your Marine amp, use a fuse of exactly the same type and rating. Us, ng a different type or rating of fuse may result in damage to your amp or marine vessel or cause a fire.
Protection Circuitry
This amplifier incorporates special protection circuitry Which will disable the amplifier if any of the following should occur: · Input overload · Short circuit
Before you drill or cut any holes, investigate your car's layout very carefully. Take special care when you work near the gas tank, fuel lines, hydraUlic lines and electrical wiring. Attach all audio system components securely within the amplifier to prevent damage, especially in an accident. [. . . ] Do not mount this amplifier so thai wire connections are unprotected, in a pinched condition, in contact with any metal surfaces in your marine vessel, or likely to be damaged by nearby objects. Before making or breaking power connections in your system, disconnect the marine vessel battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals. If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the amplifier. Using a fuse of a different type or rating may result in damage to your audio system or your amplifier which is not covered by the manufacturer's warranty.
· Do not open or attempt to repair this unit yourself. Dangerous high voltages are present which may result In electric shock. Refer any repairs to a qualified service technician.
· To avoid risk of electronic shock or damage to the amplifier, do not permit any of this equipment to become damp or wet from water or drinks. If this does occur, immediately unplug the power wires and send the amplifier to your local dealer or service center as soon as possible.
· Extremely high temperatures If any of these conditions Is detected, the amplifier will go into a self preservation mode, and the PROTECT LED on the model number badge on top of the amplifier will be illuminated.
What should I do if my amplifier PROTECT LED is illumInated?
· If there is smoke or any peculiar odor present during use or if there is damage to any of the component enclosures. immediately unplug the power cord and send the amplifier to your local dealer or service center as soon as possible.
If you observe that the PROTECT LED is on, please check the system carefully to determine what has caused the protection c1rcuit to engage.
To reset the amplifier when it is in PROTECT mode, turn the power off to the system (usually by turning off the head unit or other signal source which feeds the amplifier) and then turn it on again. If the shut down was due to either an input overload or a short circuit, be sure to correct these conditions before attempting to power up the amplifier again.
SHOCK HAZARD!There are no user-serviceable parts within the unit.
MarIne MOSFET Amplifier User's Manual - page 5 Martnc MOSFET Ampllftor User's Manual· page 4
Mounting the amplifier
1. Insert h'igh pass filter capacitors and a low pass fliller -nditJctor into the wiring as shown below. Be sure to check the table at the bottom of this page to determine the correct capacitor ar. d inductor values for the crossover frequency you wish 10 achieve,
LEFT
Speaker
to REMOTE TURN-ON 18111'1 inal 0 r head u ni l
Tri-Mode
LEFT Speaker
MINIMUM
R. IGHT
Speaker
FUSE
o IBatl I
CJ
c::J
HIgh pass filter capacitors
RIGHT Spaaker
MINIMUM
e ry
. /'
SPEAKER
IMPEOANCE 4 OHMS
SPEAKER
IMPEDANCE
40HMS
$
Q
~
Chassl$ groUf'ld point
poweA
Q
Et7
Bridged Mode
ttl
Q
~
Cha'"ssis
to REMOTE TURN-ON tennlnal 01 head unit
~I, . o, ll£l'n
Q
ground
point
ttl
Lowpass filter Inductor
SP'EAKER
IMPEDANCE
FUSE
o IBatteryI
c::::I
c::J
80HMS
SUBWOOFER
Connecr the Negmive (-) terminal of 1M speaker to /he R(-) amplifier terminal.
to 'REMOTE TllRN·ON torm lnal of I' cad un It
SPEAKER IMPEDANCE 4-8 OHMS
FUSE
COnnec!the posJtlve (+) terminal of the spooker 10 !he L(+) amplifier terminal.
o IBatteryI
c::J
CJ
Component values for 6dB Passive Crossover
FREQUENCY 80 Hz tOO Hz 120 Hz t50 Hz INDUCTOR 7. 5mH 6. 5mH 5. 5mH 4mH CAPACITOR
470uF
330uF 330uF 220uF
Marino MOSFET Amplifier Users Manual - page 10
Marine MOsFET AmplirJel USB(S Manual- page 11
Power and Speaker Wiring
h
4-Channel Amplifier
BV9995B
Power and Speaker Wiring
4-Channel Amplifier
BV9995B
Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO. To set up the amplifier to run In this mode, put the crossover switches in the FULL position. Insert high pass filter capacitors and a low pass filter inductor into the wiring as shown below. If the Protection LED stil, comes on, then the ampllfTer Is faulty and needs servicing, Check that all fuses are OK. , impedance
2 Ohm Stereo/4 Ohm Mono Bridged - - - - - 0. 01% 6Hz-50kHz 103dB 0. 01% 6Hz-50kHz 103dB
THO
Frequency response
Sl~na!·to-noi$er. . . tio
Channel separation Damping factor Crossover range low pa··
[high pass
90dS
125+ 35HZ-155Hz 200Hz (fixed)
gOdS
125+ 35Hz. -155Hz 200Hz (fixed)
Low output. Disconnect all RCA Inputs to the amplifiers, It the hiss disappears, thel plug in the component dn"vmg the amplifier and unplug Its Inputs. It IS best to set the amplifier's Input level control as low as possible. [. . . ] Disconnect all RCA Inputs to the amplifiers, It the hiss disappears, thel plug in the component dn"vmg the amplifier and unplug Its Inputs. It IS best to set the amplifier's Input level control as low as possible. Th e best sUbjective s/gna/-to-noise ratio is achieved In this manner. Try /0 s t the head unit as high 8S possible (I¥/lhout distortion) and the amp Inpu level as low as possIble. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSS BV9995B
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSS BV9995B will begin.