User manual BOSS CHAOS SE1000
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSS CHAOS SE1000. We hope that this BOSS CHAOS SE1000 user guide will be useful to you.
Manual abstract: user guide BOSS CHAOS SE1000
Detailed instructions for use are in the User's Guide.
[. . . ] When operating at 2 Ohms, the amplifiers will increase their output power by approximately 50%. The current draw will also increase by about the same amount, so be sure you have enough current to run the amplifiers into a 2 Ohm load. If you lack adequate current, your music reproduction will be distorted.
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 3
General precautions
Before installing and using your new amplifier, please become familiar with all the information contained in this manual. Dangerous high voltages are present which may result in electric shock. [. . . ] If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the amplifier. Using a fuse of a different type or rating may result in damage to your audio system or your amplifier which is not covered by the manufacturer's warranty.
Mounting the amplifier
1. Find a suitable location in the vehicle in which to mount the amplifier. Make sure there is sufficient air circulation around the intended mounting location. Mark the location for the mounting hole screws by positioning the amplifier where you wish to install it. Use a scribe or mounting screw, inserted through each of the amp's mounting holes, to mark the mounting surface. If the mounting surface is carpeted, measure the hole centers and mark with a felt tip pen. Place the amplifier in position, and attach the amplifier to the mounting surface securely using screws.
Installation precautions
Before you drill or cut any holes, investigate your car's layout very carefully. Take special care when you work near the gas tank, fuel lines, hydraulic lines and electrical wiring. Attach all audio system components securely to prevent damage, especially in an accident.
SHOCK HAZARD!There are no user-serviceable parts within the unit.
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 4
Connecting the amplifier
Before doing any wiring, look through this manual and identify the diagrams to follow for power, input and speaker connections for your particular installation. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Connect the Positive (+) terminal of the RIGHT subwoofer to the CH1 (+) amplifier terminal.
Bridged Mode
SPEAKER CONNECTIONS
FUSES
CH 1
CH2
CH3
CH4
POWER CONNECTIONS BATT+ REMOTE GROUND
CH1/2 BRIDGED
CH3/4 BRIDGED
Chassis ground point
LEFT Subwoofer
SPEAKER IMPEDANCE 4-8 OHMS
Connect the Negative (-) terminal of the LEFT subwoofer to the CH4 (-) amplifier terminal. Connect the Positive (+) terminal of the LEFT subwoofer to the CH3 (+) amplifier terminal.
to REMOTE TURN-ON terminal of head unit
FUSE
Battery
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 14
Power and Speaker Wiring
Tri-Mode
4-Channel Amplifiers
CX600, CX650, CX800 and CX1000
Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO. To set up the amplifier to run in this mode, put the crossover switches in the FULL position. Insert high pass filter capacitors and a low pass filter inductor into the wiring as shown below. Be sure to check the table at the bottom of this page to determine the correct capacitor and inductor values for the crossover frequency you wish to achieve.
Tri-Mode
Component values for 6dB Passive Crossover
FREQUENCY INDUCTOR CAPACITOR 80 Hz 100 Hz 120 Hz 150 Hz 7. 5mH 6. 5mH 5. 5mH 4mH 470uF 330uF 330uF 220uF
SPEAKER IMPEDANCE 8 OHMS
RIGHT Subwoofer
High pass filter crossover
CH3 Speaker
MINIMUM SPEAKER IMPEDANCE 4 OHMS
High pass filter crossover
CH4 Speaker
Low pass filter inductor
SPEAKER CONNECTIONS
FUSES
CH 1
CH2
CH3
CH4
POWER CONNECTIONS BATT+ REMOTE GROUND
CH1/2 BRIDGED
CH3/4 BRIDGED
Chassis ground point
High pass filter crossover
+
High pass filter crossover
CH2 Speaker
MINIMUM SPEAKER IMPEDANCE 4 OHMS
to REMOTE TURN-ON terminal of head unit
FUSE
Battery
+
Low pass filter inductor
CH1 Speaker
SPEAKER IMPEDANCE 8 OHMS
LEFT Subwoofer
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 15
Power and Speaker Wiring
5 Channel Mode
5-Channel Amplifier
CX1800
Five Channel Mode
SPEAKER IMPEDANCE 2-8 OHMS
CH5 Subwoofer
+ +
CH2 Speaker
CH1 Speaker
SPEAKER IMPEDANCE 2-8 OHMS
SPEAKERS
CH5
CH1/2 BRIDGED
CH1
CH2
FUSES
POWER CONNECTIONS GROUND REMOTE BATT+
CH3
CH3/4 BRIDGED
CH4
Chassis ground point
SPEAKER IMPEDANCE 2-8 OHMS
CH3 Speaker
to REMOTE TURN-ON terminal of head unit
CH4 Speaker
FUSE
Battery
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 16
Power and Speaker Wiring
Bridged Mode
5-Channel Amplifier
CX1800
Connect the Negative (-) terminal of the RIGHT subwoofer to the CH2 (-) amplifier terminal.
CH5 Subwoofer
Connect the Positive (+) terminal of the RIGHT subwoofer to the CH1 (+) amplifier terminal.
SPEAKER IMPEDANCE 2-8 OHMS
+
RIGHT Subwoofer
SPEAKER IMPEDANCE 4-8 OHMS
Bridged Mode
SPEAKERS
CH5
CH1/2 BRIDGED
CH1
CH2
FUSES
POWER CONNECTIONS GROUND REMOTE BATT+
CH3
CH3/4 BRIDGED
CH4
Chassis ground point
SPEAKER IMPEDANCE 4-8 OHMS
LEFT Subwoofer
FUSE
to REMOTE TURN-ON terminal of head unit
Battery
Connect the Negative (-) terminal of the LEFT subwoofer to the CH4 (-) amplifier terminal. Connect the Positive (+) terminal of the LEFT subwoofer to the CH3 (+) amplifier terminal.
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 17
Power and Speaker Wiring
Tri-Mode
5-Channel Amplifier
CX1800
Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO. To set up the amplifier to run in this mode, put the crossover switches in the FULL position. Insert high pass filter capacitors and a low pass filter inductor into the wiring as shown below. [. . . ] If the hiss disappears, then plug in the component driving the amplifier and unplug its inputs. If the hiss disappears at this point, go on until the faulty/noisy component is found. It is best to set the amplifier's input level control as low as possible. Try to set the head unit as high as possible (without distortion) and the amp input level as low as possible. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSS CHAOS SE1000
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSS CHAOS SE1000 will begin.