User manual BOSS CHAOS EXXTREME CX1100M
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSS CHAOS EXXTREME CX1100M. We hope that this BOSS CHAOS EXXTREME CX1100M user guide will be useful to you.
Manual abstract: user guide BOSS CHAOS EXXTREME CX1100M
Detailed instructions for use are in the User's Guide.
[. . . ] · CHAOS EXXTREME amplifier · Remote subwoofer level control ·High input cable with connector · Four (4) mounting screws
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 2
Features
Your new CHAOS EXXTREME amplifier features the following: · Class A-B operation · Bridgeable outputs (except CX1100M and CX2000M) · Tri-Mode capable (except CX1100M and CX2000M) · MOSFET PWM (Pulse Width Modulated) Power Supply · 2 Ohm stable stereo operation with output power increase · Thermal and speaker short protection · Soft turn-on circuit · Remote turn-on/turn-off circuit · Variable input gain control · Variable low pass crossover(s) · Fixed high pass crossover(s) · Variable 0 to +18dB Bass Boost · Nickel-plated RCA low level and high level inputs · LED power and protection indicators · Silver anodized heatsink · Remote subwoofer level control
About 2 Ohm operation
Your CHAOS EXXTREME amplifier has been designed to operate efficiently at loads down to 2 Ohms. This means that you can install four 8 Ohm speakers per channel, when using parallel wiring. Increasing the number of woofers per channel at low frequencies (below 100Hz) produces an acoustic coupling effect. [. . . ] Then connect the fuse holder to the "BATT+" connection on the amplifier. If multiple amplifiers are being used in your system, either: · Run a separate pair of cables from the battery and a chassis ground point to each amplifier. -or· Run a #4 cable from the fuse holder at the battery to a distribution block at or near the amplifier's location. Then run separate cables from the amplifier to this distribution block and to independent chassis ground points. Connect all line inputs and outputs (if used) using high-quality cables. Set all level controls to minimum position, and set all crossover controls/switches to the desired frequency points. Then set the volume control on the head unit to about 3/4 volume, and adjust the amplifier's input level control(s) to just below the level of distortion. Further fine tuning of the various controls may be necessary to obtain best results.
Don't misuse the level control!
Do not mistake the input level control for a volume control!It is designed ONLY to match the output level of your audio source to the input level of your amplifier. Do not adjust this input level to maximum unless your input level requires it. Ignoring these instructions will result in an input overload to the amplifier, and excessive audio distortion. It can also cause the protection circuit to engage.
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 5
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time!
2-Channel Amplifiers
CX250, CX450, CX550, CX750, CX950, and CX1250
Remote Subwoofer Level Control
LEFT
RIGHT
INPUT LEVEL
BASS BOOST
+
L
R+
INPUTS
CROSSOVER
T WO C HA NNE L MOS FE T P OW ER A MP LIF IE R
To Audio Outputs of head unit or signal processor
4-Channel Amplifiers
CX600, CX650, CX800, and CX1000
Remote Subwoofer Level Control
CH
1
CH
2
CH3/4 CONTROLS
CH1/2 CONTROLS
CH
FOUR CHANNEL MOS FE T P OW ER A MP LI FIE R
3
CH
4
CH
+
1
CH
2+
CH
+
3
CH
4+
INPUTS
To FRONT Audio Outputs of head unit or signal processor
To REAR Audio Outputs of head unit or signal processor
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 6
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time!
5-Channel Amplifier
CX1800
Remote Subwoofer Level Control
CH1/2 CONTROLS
CH
1
CH
3
INPUT CONTROLS
CROSSOVER
BASS BOOST
CH
5R
INPUT CONTROLS
CROSSOVER
CH
+
CH
1 3
CH
2+ 4+
CH
CH
+
2
CH
4
INPUT CONTROLS CROSSOVER BASS BOOST
CH
5L
INPUT MODE
BASS BOOST
CH5
CH5 CONTROLS
CH3/4 CONTROLS
To SUBWOOFER Audio Outputs of head unit or signal processor (if present) To FRONT Audio Outputs of head unit or signal processor To REAR Audio Outputs of head unit or signal processor
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 7
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time!
MonoBlock Amplifier
CX1100M
Remote Subwoofer Level Control
LEFT
RIGHT
+
L
R+
BASS BOOST
CROSSOVER
INPUT CONTROLS
INPUTS
MOS FE T MO NOBLOC K P OW ER A MP LI FIE R
To Audio Outputs of head unit or signal processor
MonoBlock Amplifier
CX2000M
Remote Subwoofer Level Control
LEFT
RIGHT
INPUT LEVEL
BASS BOOST
CROSSOVER FREQUENCY
+
L
R+
INPUTS
MOS FE T MO NOBLOC K P OW ER A MP LI FIE R
To Audio Outputs of head unit or signal processor
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 8
High Level Input Wiring
The high level input(s) should only be used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Connect the Negative (-) terminal of the subwoofer to the R (-) amplifier terminal.
FUSE
to REMOTE TURN-ON terminal of head unit
Battery
CHAOS EXXTREME MOSFET Amplifier User's Manual - page 12
Power and Speaker Wiring
Tri-Mode
2-Channel Amplifiers
CX250, CX450, CX550, CX750, CX950, and CX1250
Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO. [. . . ] Check that the minimum speaker impedance for the amp model is correct. In some applications, it may be necessary to add external cooling fan(s). This is usually caused by poor quality RCA cables, which can pick up radiated noise. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSS CHAOS EXXTREME CX1100M
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSS CHAOS EXXTREME CX1100M will begin.