User manual BOSS DIABLO D1800.5
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSS DIABLO D1800.5. We hope that this BOSS DIABLO D1800.5 user guide will be useful to you.
Manual abstract: user guide BOSS DIABLO D1800.5
Detailed instructions for use are in the User's Guide.
[. . . ] If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the amplifier. Using a fuse of a different type or rating may result in damage to your audio system or your amplifier which is not covered by the manufacturer's warranty.
General precautions
Before installing and using your new amplifier, please become familiar with all the information contained in this manual. Dangerous high voltages are present which may result in electric shock. · To avoid risk of electronic shock or damage to the amplifier, do not permit any of this equipment to become damp or wet from water or drinks. [. . . ] If this does occur, immediately unplug the power wires and send the amplifier to your local dealer or service center as soon as possible.
Mounting the amplifier
1. Find a suitable location in the vehicle in which to mount the amplifier. Make sure there is sufficient air circulation around the intended mounting location.
OL5KD · OL4KD · OL3KD Amplifier User's Manual - page 3
3. Mark the location for the mounting hole screws by positioning the amplifier where you wish to install it. Use a scribe or mounting screw, inserted through each of the amp's mounting holes, to mark the mounting surface. If the mounting surface is carpeted, measure the hole centers and mark with a felt tip pen. Place the amplifier in position, and attach the amplifier to the mounting surface securely using screws.
4. Then connect the fuse holder to the "BATT+" connection on the amplifier. If multiple amplifiers are being used in your system, either: · Run a separate pair of cables from the battery and a chassis ground point to each amplifier. -or· Run a #0 cable from the fuse holder at the battery to a distribution block at or near the amplifier's location. A different type of fuse or rating may result in damage or cause a fire.
Don't misuse the level control!
Do not mistake the input level control for a volume control!It is designed ONLY to match the output level of your audio source to the input level of your amplifier. Do not adjust this input level to maximum unless your input level requires it. Ignoring these instructions will result in an input overload to the amplifier, and excessive audio distortion. There are no user-serviceable parts within the unit.
OL5KD · OL4KD · OL3KD Amplifier User's Manual - page 5
Low Level Input and Speaker Wiring
Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality RCA cable for best audio performance.
SUBWOOFER Speaker
SPEAKER IMPEDANCE 1-8 OHMS
To Audio Inputs of satellite amplifier (if present)
To Audio Outputs of head unit or Subwoofer outputs of a signal processor
Remote Level Control Connections
Remote Subwoofer Level Control
PLEASE NOTE: In this manual, the OL4KD is used in all system examples, but all three models can be configured in a system in a similar manner. Although the layout of front and rear panels varies slightly between models, the controls and connectors themselves are functionally identical.
OL5KD · OL4KD · OL3KD Amplifier User's Manual - page 6
Power Connections
Without Stiffening Capacitor
Chassis ground point
to REMOTE TURN-ON terminal of head unit
FUSE
Battery
With Stiffening Capacitor
Distribution Block
Chassis ground point
Battery
FUSE
to REMOTE TURN-ON terminal of head unit
Stiffening Capacitor
Chassis ground point
OL5KD · OL4KD · OL3KD Amplifier User's Manual - page 7
Bridging Two OL5KD, Two OL4KD or Two OL3KD Amplifiers
INPUT, DATALINK AND SPEAKER CONNECTIONS
(SEE NEXT PAGE FOR POWER AND REMOTE LEVEL CONTROL CONNECTIONS)
MASTER AMPLIFIER Front panel
BRIDGED MODE SWITCH IN MASTER POSITION
To Audio Outputs of head unit or Subwoofer outputs of a signal processor
SUBWOOFER Speaker
BRIDGED MODE SWITCH IN SLAVE POSITION
+
SPEAKER IMPEDANCE 2-8 OHMS
SLAVE AMPLIFIER Front Panel
PLEASE NOTE: In this MASTER AMP/SLAVE AMP configuration, the Slave amp receives its audio signal from the Master Amp. Therefore, DO NOT USE THE INPUTS ON THE SLAVE AMP!
OL5KD · OL4KD · OL3KD Amplifier User's Manual - page 8
POWER AND REMOTE LEVEL CONTROLLER CONNECTIONS
(SEE PREVIOUS PAGE FOR INPUT, DATALINK AND SPEAKER CONNECTIONS)
MASTER AMPLIFIER Rear panel
Remote Subwoofer Level Control
Chassis ground point
SLAVE AMPLIFIER Rear Panel
PLEASE NOTE: In this MASTER AMP/SLAVE AMP configuration, the Slave amp receives its audio signal from the Master Amp. Therefore, DO NOT USE THE SUBWOOFER LEVEL CONTROL ON THE SLAVE AMP!
Distribution Block
Chassis ground point
Battery
FUSE
Stiffening Capacitor
Chassis ground point
to REMOTE TURN-ON terminal of head unit
OL5KD · OL4KD · OL3KD Amplifier User's Manual - page 9
Troubleshooting
If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous pages. If problems persist, read the following troubleshooting tips which may help eliminate the problems. [. . . ] If problems persist, read the following troubleshooting tips which may help eliminate the problems. POSSIBLE REMEDY
Check to make sure you have a good ground connection. If the Protection LED still comes on, then the amplifier is faulty and needs servicing. If the hiss disappears, then plug in the component driving the amplifier and unplug its inputs. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSS DIABLO D1800.5
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSS DIABLO D1800.5 will begin.