User manual CARVIN AG100D
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CARVIN AG100D. We hope that this CARVIN AG100D user guide will be useful to you.
Manual abstract: user guide CARVIN AG100D
Detailed instructions for use are in the User's Guide.
[. . . ] 12" PS12 or 15" PS15 woofer (depending on model purchased) 1" Titanium HF Driver with adjustable L-Pad on crossover. 12" Cabinet Response: 63Hz to 16. 5kHz
Congratulations on your purchase of the AG100D Series III amplifier. We've included all of the great features a solo performer needs, such as three independent channels with separate volume and EQ, MID sweep control, phantom mic power and 5 band Graphic EQ. Additional features include, mid & HI Contour switches on channel 1, Bass and Mid Contour switches on channel 2. [. . . ] It is suggested that the tone control settings start in their center positions where they do not effect the signal. Then, as needed, turn the turn to the right to boost, or to the left to cut to change the sound. XLR MICROPHONE & 1/4" INPUT JACKS The MIC input is designed for balanced low impedance ( microphone ) input signals. The Balanced input will reduce the common noise picked up on the microphone cables. The XLR connector is wired as per the industry standard; pin 1 is ground, pin 2 is positive and pin 3 is negative. This allows condenser microphones to be run directly without the need for batteries or other external phantom power supplies. The 1/4" jack is designed for unbalanced high impedance signals (guitar, tape deck, drum machine, etc. ). VOLUME CONTROL The VOLUME control adjusts the volume of the channel heard in the speaker, the line out jack, and the headphone jack. LO AND HI TONE CONTROLS The LO and HI tone controls are used to shape the bass and treble sound of the input signal. It is suggested that the tone control settings start in their center positions where they do not effect the signal. Then, as needed, turn the turn to the right to boost, or turn to the left to cut to change the sound. DIGITAL SIGNAL PROCESSING The 24 bit processor will provide a host of awesome sounding effects that include: Flange, Reverb, Echo, & Chorus. The master EFFECT 1 & 2 control will adjust the volume level of the selected effect. Remember each channel has its own EFFECT send level that will adjust the amount of signal sent to the effects processor. (Note: When adjusting the effects on either channel, an audible noise may be heard).
EFFECT PARAMETERS Each of the four effects has a variable parameter that can be easily adjusted. ECHO: When the top SELECT control is at the "7 O-clock" position, it is selected to the first ECHO setting where you get a single repeat echo (minimal regeneration). Turning the PARAMETER control to 1 will provide the shortest delay time between the original signal and the echo. Increasing the PARAMETER control to the right will increase the time delay between the original signal and the echo. To increase the number of echoes, turn the SELECT control clockwise to "9 O-clock" (maximum regeneration). REVERB: When the SELECT control is at the "10 O-clock" position, it is selected
3
12
3 6 9 12
3
3
3 6 9 6 9 12
3 6 9
3 6 9 12
3 6 9 6 9
3
3 6 9
EFF2
3 6 9 12
3 6 9
3 6 9 12
3 6 9 6 9
3
3 6 9
EFF2
RE
RE
LO 0
12
12
LO
12
EFF1
12
12
EFF1
PARAMETER
MID
HI
MID
INPUT 1
VOLUME 456 3 7 2 8 1 9 0 10
EFF
OFF
INPUT 2 3 6 9
3 6 9
EFF1
EFF2
VOLUME 456 3 7 2 8 1 9 0 10
MIC
TAPE/CD
VOLUME 456 3 7 2 8 1 9 0 10
456 3 7 2 8 1 9 0 10
PK
3 2 1
456
0
7 8 9 10
PK
CH 1
CH 2
CH 3
3 2 1
LEVEL 5 4 6 456 3 7 7 8 82 1 9 9 0 10 0 10
1
2
3
6
7
9
10
E
E
FREQ GAIN 1K MID 0 3 3 800 2K 6 6 6 9 9 9 300 3K 12 12 12
HIGH 0 3
LO 0
HI 0
EFF
OFF
LO 0
HI 0
EFF
OFF
V
EFF1
ER
B
CH
O
EFF2
V
ER
B
CH
O
ACOUSTIC GUITAR AMP
DUAL 24-BIT EFFECTS
AG100D
R
US
R
US
6 9 12
HO
HO
FLA N
FLA N
EC
EC
G
G
+
12 8 4 0 4 8 12
GRAPHIC EQ
POWER
3 2 1
-
7 8 9 0 10 MASTER
456
100
250
800
6K
12K
13
14
15
EFF1
RE RE
V
EFF2
O
R
V
ER
B
CH
ER
B
CH
O
R
PARAMETER
CHORUS: When the SELECT control is at the "1 O-clock" position it is selected to the first CHORUS setting. 456 456 3 7 3 7 Turning the SELECT control clockwise will increase the 2 8 2 8 1 9 1 9 amount reverb in the chorus. Turning the PARAMETER 0 10 0 10 control to 1 will provide a minimal chorus depth setting. [. . . ] Refer to replacement text on the unit for correct fuse type.
HELP SECTION 1) AMP WILL NOT TURN ON Check the power to the amp. Check for tripped circuit breakers, unplugged extension cords or power-strip switches that may be turned off. After you have verified there is AC power and the amp still doesn't work, your unit will require servicing. 2) MAINTENANCE To bring back the new look, your AG100D cabinet can be wiped with mild detergent and/or a warm damp soft cloth. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CARVIN AG100D
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CARVIN AG100D will begin.