User manual CARVIN F1200

[. . . ] 2. BATTERY Insert 2 fresh AA alkaline batteries into the transmitter. CHANNEL CHECK Check that both the transmitter and receiver are set to corresponding channel. If multiple systems are used, each system must be set to their own channel. 3. BELT PACK SETTINGS (USM16BP only) Connect the instrument cable or mic to the Belt-pack. RECEIVER POWER ON Turn the Volume control of the receiver down and turn down the volume on the unit this system is mounted in. [. . . ] This indicates that maximum transmitter modulation without distortion has been reached. You can adjust the AF level of the transmitter using the included small screwdriver. RECEIVER USM16 Receiving System Stability Signal-to-noise Image Rejection THD RF Sensitivity Connection Audio Output Power Supply Dimensions Diversity- PLL Synthesized ± 0. 005% >100 dB >60 dB <1% @ 1kHz -107dBµ for 12 dB S/N AD 20 pin PCB edgecard, 0. 156" pitch. Power through connector only W: 3. 30" (84mm) H: 1. 22" (31 mm) D: 5. 375" (136. 5 mm) to PCB, 4. 88" (124mm) to case. 1 lbs (. 5 kgs) USM-KIT (REQUIRED for mounting, holds up to 2 receivers) 90 days BELT PACK TRANSMITTER USM16BP RF Power Output Spurious Rejection Stability Frequency Deviation Battery S/N Ratio Current Consumption Dimensions Net Wt (no battery) Warranty 3 mW < -60 dBC ± 0. 005% ± 48kHz AA 1. 5v alkaline qty 2 >100dB (1kHz-A) 100mA typical 2. 56" W x 4" H x 1" D 2. 8 oz (78 grams) 90 days RECEIVING INSPECTION--read before getting started INSPECT YOUR WIRELESS SYSTEM FOR ANY DAMAGE which may have occurred during shipping. If any damage is found, please notify the shipping company and CARVIN immediately. In the event you have to re-ship your unit, always use the original carton and packing material. CARVIN and the shipping company are not liable for any damage caused by improper packing. Please allow several days for the rest of your order to arrive before inquiring. RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual for your records. Keep your portion of the card and return the portion with your name and comments to us. HANDHELD MIC TRANSMITTER F1200 Polar Pattern RF Power Output Spurious Emissions Dynamic Range Battery Current Consumption Battery Life Dimensions Net Wt (no battery) Accessory Included Warranty Unidirectional 3 mW Under federal regulations >100 dB AA 1. 5v alkaline qty 2 30 mA typical Approx. 12. 7 oz (360 grams) mic clip 90 days Net Weight Accessories Warranty For your records, you may wish to record the following information. C Green Power Indicator Channel Selector Push the round button to release the cable Transmitter ON/OFF switch USM16-MC HAND HELD MIC Fig. G Removable Battery dock Remove cap to turn ON and select channel USM16-BP BELT-PACK TRANSMITTER 1. A metal belt clip case protects the transmitter and features a heavy-duty clip. To access the rear controls, push the two side release buttons on the belt clip. Insert fresh AA alkaline batteries, observing correct polarity as marked inside the battery compartment. SENSITIVITY Fig B. The transmitter's sensitivity controls are located on the rear. Use the mini screwdriver to first set the Sensitivity switch to 0 for instruments or -20 for microphones. Use the mini screwdriver to make fine gain adjustments to the Sensitivity AF Gain for optimal transmitter volume. When the indicator becomes very dim or goes out, replace the batteries for continued operation. If you encounter signal interference, try selecting an alternate channel. The mini XLR input jack will connect a Lavaliere mic, headset mic, or instrument cable to the transmitter. [. . . ] F Connect the mic cable to the transmitter's mini XLR input jack. Adjust the mic position to minimize air from hitting the mic. UX-LP1 LAVALIERE MIC (OPTION) 1. G Connect the lavaliere mic cable to the transmitter's mini XLR input jack. For optimum sound, position the mic as close to the mouth with the top of the mic facing up. [. . . ]