User manual CAT EYE CC-7000 VECTRA

[. . . ] The features are as follows: Altimeter Functions: · Measures current altitude (above sea level), trip altitude gain, total altitude gain in a temperaturecompensated 1 meter resolution. · Can be used for activities other than bicycling, with accessory parts. Cyclocomputer Functions: · · · · · Current speed · Maximum speed Average speed · Total distance Trip distance · Elapsed time Clock time · Auto (Automatic start/stop) function Can reset maximum speed, average speed, trip distance, elapsed time. Aspects of Main Unit: · The screen backlight enables you to read the computer screen even at night. · Any data stored in memory (total distance, total altitude gain, wheel circumference etc. ) will not be lost with an all-clear operation or by changing the battery. Before operating, thoroughly familiarize yourself with this manual so that you understand the functions completely. [. . . ] In this mode, the main display (upper line) always shows the current speed. 7 E D B C · Each main mode has its respective sub mode. To switch back to the main mode from the sub mode, just press this button ordinarily. To shift from one mode to another, it is necessary to switch back to the main mode (from the sub mode) each time. B S/S (Start/Stop) Button (Upper Button) A Fig. 8 · With each press, this button starts or stops measuring trip distance (D), elapsed time (T) and average speed (A). During operation, the speed scale symbol or temperature scale symbol flashes. · In the Auto (automatic start/stop) function [when AT symbol is on], this button does not work (refer to page 12). C Light Button (Right Side Button) Set Button (Left Side Button) · With each press, the display is backlit for approx. 3 seconds. D How the mode shifts by the MODE button This button is used for the following operations: MAIN MODE Current Speed Current Altitude SUB MODE · For correcting the current altitude Trip Alt. Gain x1000 Total Alt. Gain Current Speed 12-Hour Clock Current Speed T Elapsed Time Current Speed A Average Speed Current Speed D Trip Distance Fig. 9 Current Speed M Max. O Total Distance Press ordinarily Hold down mode (but only when the current speed is zero) ---- refer to page 10 press this button in the · For shifting the altitude measuring mode press this button in the total altitude and the trip altitude gain mode ---------------- refer to page 10 · For switching on/off the Auto (automatic start/stop) function press this button in T, D or A mode (but only in complete stop state) -------------- refer to page 12 · For changing the wheel circumference press this button in O (total distance) mode (but only when the current speed is zero) --------------------------------------------------------------------------------------------------------- refer to page 7 · For setting clock time press this button in the clock time mode (but only when the current speed is zero) ---- refer to page 7 AC (All Clear) Button (on the back) This button erases the data stored in memory. Press this button when setting up the unit for bicycle for the first time, or when irregular display occurs. After pressing this AC button, all displays illuminate and then only the "km/h" symbol appears. The accumulated data (total distance and total altitude gain) and the stored wheel circumference are not deleted by this operation. After this operation, only the speed scale, temperature scale and clock time must be set again, according to "Main Unit Preparation" (refer to page 7). 8 Reset When the S/S button and the Mode button are pressed simultaneously, the following data can be reset, depending on the mode. For resetting trip distance(D), elapsed time(T), average speed(A) and maximum speed (M): In other modes than altitude measuring mode, press the two buttons simultaneously; then the data of D, T, A and M returns to zero. E For resetting the trip altitude gain: In the sub mode showing the trip altitude gain and total altitude gain, press the two buttons simultaneously; then the data of the trip altitude gain( ) returns to zero. For resetting the current altitude correction value: In the main mode showing the current altitude ( ), press the two buttons simultaneously; then the current altitude correction value will be zero and the data will be reset to the initial value of "International Standard Atmosphere" (ISO 2533). HOW TO USE AS AN ALTIMETER Correlation between above sea level and pressure extract from ISO 2533 (Table 1) A. S. Level Pres. Insert the band B into the slit of the band A, and put the rubber pad inside of the band A (Fig. Adjust the length in order that the screw-fastening part of the bands are parallel when mounted to the fork (Fig. Mount the adjusted bands to the fork along with the speed sensor and sensor holster, by temporarily tightening the screw (Fig. Align the magnet's center and the sensor's marking line (Fig. 18), and clearance between the magnet and the sensor should be 2mm (Fig. Note: If the space between the fork and the spokes are too narrow, mount the sensor without the holster. Magnet Spoke Rubber Pad Parallel Sensor Band A Fig. 14 Fig. 15 Fig. 16 Speed Sensor Sensor Band B Marking Line of Sensor Magnet Speed Sensor Center of the Magnet Front Fork Sensor Holster Fig. 17 Fig. 18 About 2 mm Fig. 19 11 Bracket Bracket E Wire Rubber Pad Fig. 21 Wire Securing Tape Slide Speed Sensor Fig. 20 Front Fig. 22 Lever · Secure the wire with the wire securing tape as in Fig. When adjusting the length, be careful that the wire will not hinder handlebar operation. · By using the rubber pad, attach the bracket close to the handlebar stem (Fig. 21). Mounting Main Unit Slide the main unit onto the bracket from front until it clicks into position. To remove the unit, pull it off forward while pushing down the lever (Fig. If not, adjust the relative positions of the magnet and the sensor again following the instructions. 2. [. . . ] 25) When the current speed does not appear, short-circuit the two contacts on the back with metal a few times. (*After replacing the battery, be sure to press the AC button and to reset the speed scale, temperature scale and the clock time again. ) 15 Fig. 25 E Incorrect data appears. Press the AC button and reset the speed scale and the clock time again. Are the magnet's center and the sensor's marking line aligning? [. . . ]