User manual DA-LITE 33P REV 11-08
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DA-LITE 33P. We hope that this DA-LITE 33P user guide will be useful to you.
You may also download the following manuals related to this product:
DA-LITE 33P REV 08-10 (710 ko)
Manual abstract: user guide DA-LITE 33PREV 11-08
Detailed instructions for use are in the User's Guide.
[. . . ] 11 / 08
Caution: This product is designed for ceiling
installation only. Qualified personnel using the appropriate fasteners should mount the Pivoting DaLift. [. . . ] Remove contents from carton and examine for damaged or missing parts.
SAVE THESE INSTRUCTIONS Required Tools:
7/16" wrench 1/2" wrench 9/16" wrench Phillips screwdriver
CHANNEL MOUNTED TO STRUCTURAL CEILING (NOT SUPPLIED)
3/8" ALLTHREAD, NUTS, AND WASHERS (NOT SUPPLIED)
SUSPENDED CEILING GRID AND TILE
PROJECTED IMAGE TRIM 120V AC CONNECTION PROJECTOR 11/2" CONDUIT KNOCKOUT (FOR PROJECTOR SIGNAL CABLE) 1/2" CONDUIT KNOCKOUT (FOR WALL SWITCH OR OPTIONAL REMOTE RECEIVER) CEILING TILE CEILING TILE HOLDER CAP CEILING TILE HOLDER
Figure 1
CHANNEL (NOT SUPPLIED)
TRIM PROJECTOR CEILING TILE HOLDER CEILING TILE HOLDER CAP CEILING TILE
Figure 2
DALIFT MODEL 26P 33P "W"
"L" 231/2" 301/2"
"W" 7" TO 141/4" 111/2" TO 183/4"
"L"
CENTERLINE OF ALLTHREAD
Figure 3
5/16" CENTERLINE OF ALLTHREAD TO CUTOUT
2. Thumbnuts can be used for fine tuning projector position in next step.
Figure 6
NUTS FOR RIGHT TO LEFT ADJUSTMENT NUTS FOR FORE AND AFT ADJUSTMENT
5.
Figure 7
PROJECTOR
DALIFT MODEL 26P
"A" 161/2" 21"
"B" 153/8" 197/8"
6. Determine where the projector will be located and make a hole in the ceiling and create a tile for the DaLift.
CUTOUT
"A"
TRIM PIECE HAS TO FIT INSIDE CUTOUT SCRAP
Figure 8
TILE HAS TO FIT INSIDE CEILING TILE HOLDER
"B"
7.
CHANNEL NOTE: ITEMS CALLED OUT ARE NOT SUPPLIED
3/8" ALLTHREAD 3/8" HEX NUT
3/8" FLAT WASHER 3/8" FLAT WASHER
3/8" LOCK HEX NUT
Figure 9
"UP"
8. The "Stop" button is needed only for intermediate stopping.
CONNECT TO 120V AC "STOP" "DOWN"
WARNING! AVOID PINCH POINTS WHEN OPERATING DALIFT WITH THIS SWITCH
CEILING TILE HOLDER CAP
Figure 10
11. Install Ceiling Tile cutout from step 6 into Ceiling Tile Holder and assemble Ceiling Tile Holder Cap.
Figure 13
CABLE STORAGE
WHITE WIRE
BLACK WIRE RED WIRE
UP
STOP
RED WIRES WHITE WIRES BLACK WIRES
DOWN
120V AC 60 Hz SUPPLY
HOT COMMON GROUND
BLACK (HOT) WHITE (COMMON) GREEN (GROUND)
Figure 14
RECOMMENDED WIRE SIZE: 12 AWG
Figure 15
RECOMMENDED WIRE SIZE: 2024 AWG
Pivoting DaLift Plenum Cover 26P and 33P
Form E454 Rev.
Caution: This product is designed for ceiling
installation only. Qualified personnel using the appropriate fasteners should mount the Pivoting DaLift and Plenum Cover. [. . . ] Remove contents from carton and examine for damaged or missing parts.
SAVE THESE INSTRUCTIONS Required Tools:
Phillips screwdriver
REMOVE END PIECE
Figure 1
A
2. Secure the Plenum Cover End to the DaLift using the fasteners from step 2. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE DA-LITE 33P
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DA-LITE 33P will begin.