Detailed instructions for use are in the User's Guide.
[. . . ] INSTRUCTION MANUAL Color Television
DTQ 25S3FC DTQ 27S3FC DTQ 27S4FC
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
NOTE TO CATV SYSTEM INSTALLER
THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.
CAUTION
The AC power cord provided with this product is polarized (one blade wider than the other). To prevent electrical shock, match wide blade of plug to wide slot, fully insert the AC plug into a standard 120V~, 60Hz polarized outlet.
NOTE
Never connect the plug to an electrical source other than one providing 120V 60Hz power. [. . . ] The current channel number and status will be displayed.
Chapter 3: Operating Your TV
11
Changing the TV's Input
Normally, your TV displays the signal coming through the antenna terminal. However, If you've connected another component to your TV(such as a VCR) using the Video/Audio input, you will want to be able to view the signal from the component. To do this, you will need to switch from the ` TV ' input to the ` Line1, Line2 ' Input, as follows: 1 With the TV on, press the MENU button twice, then " Set-Up " menu will appear. 3 Press the CVOLB buttons to change from ` TV ' to ` Line1, Line 2 '. 4 Wait 10 seconds, or press the MENU button to return to normal TV viewing.
DTQ-27S3FC/DTQ-27S4FC
2
Set-Up
Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV
Select Adjust Next
3-1 Set-Up
Language : Input : English Line1
Select
Adjust
Next
3-2 Set-Up
Language : Input : English Line2
Select
Adjust
Next
DTQ-25S3FC
2 3
Set-Up
Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV
Select Adjust Next
Set-Up
Language : Input : English Line
Select
Adjust
Next
12
Chapter 3: Operating Your TV
Adjusting Video Settings
You may wish to adjust the video settings (e. To do so, follow these directions: 1 With the TV on, press the MENU button, then "Video" menu will appear. 3 Use the WCHV buttons to select the video setting you wish to adjust. 4 Use the CVOLB buttons to adjust the video setting to the level you prefer. 6 When you are finished, press the MENU button to return to normal TV viewing. 7 Video button on the Remote Controller can do the same function.
1
2
3
Video
Settings : Contrast Brightness Sharpness Color Tint
Select Adjust
Video
Custom Settings : Contrast Brightness Sharpness Color Tint
Select Adjust
Video
Preset Settings : Contrast Brightness Sharpness Color Tint
Select Adjust
Preset
Next
Next
Next
4
5
6
Contrast
Brightness
Chapter 3: Operating Your TV
13
Returning to the factory settings If you would like to return to the original video settings, as they were calibrated at the factory, follow these steps : 1 With the TV on, press the MENU button, then "Video" menu will appear. 2 Press the CVOLB buttons to set the "Settings" to `Preset'. The TV will remember the `Custom' settings you had previously chosen. When you set "Settings" to `Custom' again, your previous custom settings will be restored.
1 2
Video
Settings : Contrast Brightness Sharpness Color Tint
Select Adjust
Video
Custom Settings : Contrast Brightness Sharpness Color Tint
Select Adjust
Preset
Next
Next
Descriptions of video settings The contrast setting controls the relation between the light and black areas of the screen. If the light areas are too bright and are losing details, press the CVOL button; if the picture is gray and lacks contrast, press the VOLB button. The brightness setting controls the overall amount of light in the picture. If the picture is too bright, press the CVOL button; if the picture is too dark, press the VOLB button. If the TV shows multiple vertical lines at the edges of an object, press the CVOL button; if the vertical edges of on-screen objects are fuzzy, press the VOLB button. If the color is over-saturated, press the CVOL button; if the color is washed out, press the VOLB button. The tint setting controls the relationship of red and green in a picture. If flesh tones seem too red or purple, press the VOLB button; if flesh tones are too green, press the CVOL button.
14
Chapter 3: Operating Your TV
CHAPTER
4
Using Timer Functions
Your TV has a built in-clock, and you can set the TV to turn on and off at times that you select. You can also set your TV to turn off after counting down a certain amount of time.
Setting the Clock
1 With the TV turned on, press the MENU button until "Time" menu is displayed. If you hold down either CVOL or VOLB button, the corresponding numbers will change more quickly. [. . . ] If your TV receives a stereo sound (or SAP) broadcast, when the TV is turned on, select another channel or press the RECALL button on the remote control until the word "Stereo"(or "SAP") is displayed on the screen.
Listening to stereo sound
1 With the TV turned on, press the MENU button until "Audio" menu is displayed. 3 Press the CVOLB buttons repeatedly until "Stereo" is displayed. 4 Press the button twice or wait a few seconds to return to normal TV viewing. Your TV will then automatically reproduce either stereo or monaural sound, whichever is broadcast.
1~2 Audio
Audio Mode: Bass Treble Balance Mono
3
Audio
Audio Mode: Bass Treble Balance Stereo
Select
Adjust
Exit
Select
Adjust
Exit
Listening to second Language
1 Follow steps 1~2 in "Listening to stereo sound" above. [. . . ]