User manual EVINRUDE 1,5 TO 35 HP 1965-1978
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual EVINRUDE 1,5 TO 35 HP 1965-1978. We hope that this EVINRUDE 1,5 TO 35 HP 1965-1978 user guide will be useful to you.
Manual abstract: user guide EVINRUDE 1,5 TO 35 HP 1965-1978
Detailed instructions for use are in the User's Guide.
[. . . ] You can be proud you purchased an Evinrude E-TEC outboard with the following benefits. · Easy to Own and Operate This means fewer time-consuming and expensive maintenance requirements. Your Evinrude E-TEC outboard has a debris-resistant, flow-through cooling system, and requires no break-in, oil changes, oil filter changes, or expensive winterizing. Best of all, there is no scheduled dealer maintenance for three years of normal recreational use--only common sense pre-launch checks and periodic checks for corrosion when used in salt-water applications. [. . . ] Fuse
3) Raise flywheel guard from the fittings by pulling up on the front two fastening tabs.
1 1
1. Fastening tabs
27
Using Your E-TEC Outboard
Anti-Corrosion Anodes
DANGER
Contact with a rotating flywheel can cause severe personal injury. Use extreme care in re-fastening the flywheel guard on the fastening tabs. Keep hands, hair, and clothing away from coming in direct contact with rotating parts. If equipped, snap emergency stop switch lanyard to secure place on clothing. Proceed immediately to nearest landing for service.
Your outboard is equipped with one or more anodes that protect it from galvanic corrosion. See your Dealer for replacements.
SALT WATER
Additional anodic protection for the outboard has been provided for use in salt or brackish water. Upon removal from salt water, leave outboard in a vertical position until its cooling system has drained. During long periods of mooring, tilt the gearcase out of the water, except in Galvanic corrosion destroys underwater metfreezing temperatures. Flush the outboard, if al parts and can occur in fresh or salt water; desired. however, salt, brackish, and polluted waters will accelerate corrosion. Clean and wax upper and lower engine covers (annually or every 100 hours). In salt water applications, check lubrication points and corrosion protection. Use Evinrude anti-corrosion spray or Evinrude "6 in 1" multi-purpose lubricant (annually or 100 hours).
30
MAINTENANCE
31
Maintenance
ENGINE EMISSIONS INFORMATION
Maintenance, replacement, or repair of the emission control devices and systems may be performed by any marine SI (spark ignition) engine repair establishments or individual. EPA Emission Regulations All new 1999 and more recent Evinrude outboards manufactured by Bombardier are certified to the EPA as conforming to the requirements of the regulations for the control of air pollution from new watercraft marine spark ignition engines. This certification is contingent on certain adjustments being set to factory standards. For this reason, the factory procedure for servicing the product must be strictly followed and, whenever practicable, returned to the original intent of the design. The responsibilities listed above are general and in no way a complete listing of the rules and regulations pertaining to the EPA requirements on exhaust emissions for marine products. For more detailed information on this subject, you may contact the following locations:
Manufacturer's Responsibility
Beginning with 1999 model year outboards, manufacturers of marine engines must determine the exhaust emission levels for each engine horsepower family and certify these outboards with the United States of America Environmental Protection Agency (EPA). An emissions control information label, showing emission levels and engine specifications, must be placed on each outboard at the time of manufacture.
Dealer's Responsibility
When performing service on all 1999 and more recent Evinrude outboards that carry an VIA U. S. POSTAL SERVICE: emissions control information label, adjustOffice of Mobile Sources ments must be kept within published factory Engine Programs and Compliance Division specifications. Engine Compliance Programs Replacement or repair of any emission relatGroup (6403J) ed component must be executed in a manner that maintains emission levels within the pre401 M St. [. . . ] Please contact your Dealer or Distributor.
Change of address
Model number Serial Number
Change of ownership
Old address / Previous owner
Last name First name Address City Zip code Phone number Signature Date Country State M. I.
New address / New owner
Last name First name Address City Zip code Phone number Country State M. I.
51
Product Information
52
CONFIRMATION OF RECEIPT
Your Dealer
Name:
Address:
Upon delivery of your new Evinrude/Johnson outboard, complete and sign the form below. Your Dealer will take receipt of the form for their records.
Receipt
Name:
Address:
Owner of Model No: Serial No: (To be completed by customer or selling Dealer) The Dealer named on this document has instructed me on the operation, maintenance, safety features and warranty policy, all of which I understand and agree to be bound with. I am also satisfied with the predelivery set-up and inspection of my Evinrude/Johnson outboard. Signature: Date:
53
Product Information
54
OWNER'S NOTES
55
Product Information
Readiness Test
The Operator's Readiness Test. . . . [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE EVINRUDE 1,5 TO 35 HP 1965-1978
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual EVINRUDE 1,5 TO 35 HP 1965-1978 will begin.