User manual FUTABA 8FG

[. . . ] 8FG 8 CHANNEL RADIO CONTROL SYSTEM FASST-2. 4GHz Multi-ch/7-ch mode selectable INSTRUCTION MANUAL 1M23N22201 TABLE OF CONTENTS INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Fail Safe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2 <Table of Contents> FUNCTIONS OF MODEL MENU . . . . . . . . . . . . . . . . . [. . . ] Touch the RTN button to end adjustment and return to the cursor mode. 1. Move the cursor to the [MODE] item and touch the RTN button to switch to the data input mode. Move the cursor to the [T1-T4 MEMORY] item and touch the RTN button to switch to the data input mode. Select the ACT mode by scrolling the touch *The display blinks. [COMB. ]: Combination mode. (To terminate the input and return to the original state, touch the S1 button. ) [INH]: Inhibited [ACT]: Activated 3. (To terminate the input and return to the original state, touch the S1 button. ) 4. At the home screen, move the cursor to the trim you want to change and touch the RTN for one second. The trim display is moved to the center position. the actual trim position. 1. Move the cursor to the [UNIT] item and 67 DATA RESET Model memory setting data reset. trim settings or all of the settings saved in the active model memory. T1~T4: Reset the digital trim setting. *The trim step amount and trim rate are not reset. access the setup screen shown below by touching the RTN button. <SensorTouchTM> Scrolling and return to the Linkage menu by touching the RTN button. 1. Move the cursor to the item you want to reset and touch the RTN button. (Touch the S1 button to cease resetting. ) [T1-T4]: Resets only the T1-T4 [ALL MODEL SETTING]: Resets all the functions in the Linkage menu and Model menu except the frequency, model select, and model type functions. 68 and other functions common to all model types. model type matched to the aircraft. If a different If either a helicopter or glider have been selected Note: The T8FG is designed so that the airplane and glider (including EP glider) model types are compatible with aircraft of similar type wings. This section outlines the relationship between the functions common to airplanes and gliders, except some dedicated functions, and model type. The setting menus will depend on the number of servos and other differences according to the wing type used. The setup screens in the instruction manual are typical examples. touching the MDL button twice at the home screen, etc. <SensorTouchTM> Scrolling and return to the home screen by touching the RTN button. model type. access the setup screen by touching the RTN button. manual. completely customizable program mixes. The D/R curve of a T8FG transmitter may be 69 CONDITION Flight condition's switch assignment, copy, priority change and condition delay can be set. [except airplane type] Unnecessary fuselage motion which may be generated when there are sudden changes in the servo positions and when there are variations in the operating time between channels during condition switching. The delay can be set for each channel to ensure maximum performance from your aircraft. Please note this is not applicable to airplane type selections. Note: To prevent accidental activation of any switch setting of those unused conditions to null [--]. after a delay corresponding to the set amount. operational priority may be customized as desired. access the setup screen shown below by touching the RTN button. <SensorTouchTM> Scrolling and return to the Model menu by touching the RTN button. 1. Move the cursor to the switch item of the condition you want to select/delete and access the switch setup screen by touching the RTN button and select the switch and ON direction. Select the copy destination condition by scrolling the touch sensor. Then, touch the RTN button. *The current condition can not be selected for the copy destination condition. 3. Move the cursor to the [SOURCE] item and touch the RTN button to switch to the data input mode. [. . . ] The timers may be set to start and stop from the call the setup screen shown below by touching the RTN button. <SensorTouchTM> Scrolling and return to the home screen by touching the RTN button. [START]: Start/Stop switch [RESET]: Reset switch Move the cursor to the [MODE] item and touch the RTN button to switch to the data input mode. Select the mode by scrolling the touch sensor and touch the RTN button. [UP]: Up timer [DOWN]: Down timer Move the cursor to the [MEMORY] item and touch the RTN button to switch to the data input mode. Select the mode by scrolling the touch sensor and touch the RTN button. [. . . ]