User manual GEMINI CFX-40

[. . . ] POWER-CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. LIGHTNING: For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. [. . . ] Prior to use, we suggest that you carefully read all the instructions. Connect any type of device that will accept a digital signal, such as DAT, MD, HARD DRIVE, ETC to the COAXIAL (5) INPUT on the rear panel of the transport to record a digital signal. ANTI-SHOCK BUFFER MEMORY: With 12 SECONDS OF ANTI-SHOCK BUFFER MEMORY, each side of the CD player stores 6 seconds of future play to ensure that any harsh movement or bumping of the unit will not interrupt play and play will continue smoothly. 4 DSP effects using Jog wheel parameter control New "State of the art" Master tempo, full functionality 100% pitch 3 Hot Cue points Seamless looping Real time scratching Anti-shock using RAM buffer memory Large soft touch rubber Jog Wheel Variable pitch control of 4% 12% 24% & 100% Large LCD screen with blue LED backlight. Direct access keypad with full programmable feature LED target light for draw mechanism POWER: After making sure that the VOLTAGE SELECTOR (1) switch, found on the rear panel, is properly set, plug the unit in and press the POWER (6) button. DISC TRAY: The DISC TRAY (7) is where the CD is held during loading, unloading and playback. Do not use this CD Player at temperatures below 41°F/5°C or higher than 95°F/35°C. The apparatus should not be exposed to dripping or splashing and no objects filled with liquids such as vases should be placed on the apparatus. When disconnecting the power cord from an AC outlet, always grasp it by the plug. To prevent electric shock, do not remove the cover or the bottom screws. STOP: Press the STOP (8) button to STOP a CD in PLAY mode and to also load or remove a CD from the DISC TRAY (7). DISPLAY: The DISPLAY (9) shows the track number, pitch value, singleauto cue, continue (for continuous play), and 3 different time displays. These time displays are time elapsed on the track, time remaining on the disc and time remaining on the track. The display flashes slowly when the track has 15 seconds remaining and pulses rapidly when playing time is down to 5 seconds. PLAY/PAUSE : Each press of the PLAY/PAUSE BUTTON (11) causes the operation to change from play to pause or from pause back to play. CUE/PREVIEW: With the unit in the PLAY mode and after the CUE POINT has been programmed, pressing CUE/PREVIEW (12) will cause the CD player to enter the PAUSE mode at the programmed CUE POINT. Holding down the CUE/PREVIEW (12) button changes the function to PREVIEW and starts the CD from the programmed CUE POINT. releasing the CUE/ PREVIEW (12) button will return the CD laser to the preset CUE POINT. Since the CFX-40 is a dual CD player, most of the functions and controls are duplicated on both sides of the CD player. To eliminate confusion and to make the drawings easier to understand, we will only number the left side functions and controls. Place the head of a screwdriver in the center of the VOLTAGE SELECTOR SWITCH (1) found on the rear panel. Slide the switch left for 115 volts or push the switch right for 230 volts. [. . . ] Move the JOG WHEEL (21) to the precise spot you want play to begin and push the PLAY/PAUSE (11) button to memorize the CUE POINT. Push the PLAY/PAUSE BUTTON (11), and the unit will instantly play from the spot selected. To fine tune a CUE POINT, pause play at the memorized CUE POINT (the CUE/PREVIEW (12) LED will glow and the PLAY/PAUSE (11) LED will blink), then use the JOG WHEEL (21) to scan frame by frame (1/ 75th of a second) to where you want play to begin (the CUE LED will blink while you scan). Make sure that the VOLTAGE SELECTOR (1) switch, found on the rear panel, is set for the proper voltage. [. . . ]