User manual GRANDSTREAM HT496

[. . . ] Grandstream Networks, Inc. HT496 Dual FXS Port Analog Telephone Adaptor HT496 User Manual Firmware Version 1. 0. 3. 86 www. grandstream. com support@grandstream. com TABLE OF CONTENTS HT496 User Manual WELCOME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY COMPLIANCES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Type in "ipconfig /renew", the computer gets an IP address in 192. 168. 2. x segment by default 5. FROM THE WAN PORT: The WAN port HTML configuration option is disabled by default from factory. Find the WAN IP address of the HT496using voice prompt menu option 02. Access the HT496Web Configuration page by the following URI via WAN port: http://HandyTone-IP-Address (the HandyTone-IP-Address is the WAN IP address for the HT496). NOTE: If using a web browser to enter the configuration page, strip the leading "0"s because the browser will parse in octet. if the IP address is: 192. 168. 001. 014, please type in: 192. 168. 1. 14). Grandstream Networks, Inc. HT496 User Manual Firmware 1. 0. 3. 86 Page 16 of 29 Last Updated: 7/2007 END USER CONFIGURATION Once the HTTP request is sent from a Web browser, the user will see a log in screen. There are two default passwords for the login page: User Level: End User Level Administrator Level Password: 123 admin Web pages allowed: Only Status and Basic Settings Browse all pages Only an administrator can access the "ADVANCED SETTING" configuration page. FIGURE 3: SCREENSHOT OF CONFIGURATION LOG- IN PAGE NOTE: If you cannot log into the configuration page by using default password, please check with the VoIP service provider. The service provider may have provisioned and configured the device for you. The Basic Configuration Page is the first web GUI the user will see. Grandstream Networks, Inc. HT496 User Manual Firmware 1. 0. 3. 86 Page 17 of 29 Last Updated: 7/2007 TABLE 7: HT496 Basic Configuration Settings Definitions End User Password Password to access the Web Configuration Menu. There are two modes to operate the HT496: DHCP mode: all the field values for the Static IP mode are not used (even though they are still saved in the Flash memory. ) The HT496 acquires its IP address from the first DHCP server it discovers from the LAN it is connected. The HT496 will establish a PPPoE session if any of the PPPoE fields is set. Static IP mode: configure the IP address, Subnet Mask, Default Router IP address, DNS Server 1 (primary), DNS Server 2 (secondary) fields. This field is optional but may be required by some Internet Service Providers. This option specifies the domain name that client should use when resolving hostnames via the Domain Name System. Necessary if ISP requires you to use a PPPoE (Point to Point Protocol over Ethernet) connection. If your ISP uses a service name for the PPPoE connection, enter the service name here. Controls how the date/time displays according to the specified time zone. Web Port IP Address DHCP hostname DHCP domain DHCP vendor class ID PPPoE account ID PPPoE password PPPoE Service Name Time Zone Grandstream Networks, Inc. HT496 User Manual Firmware 1. 0. 3. 86 Page 18 of 29 Last Updated: 7/2007 Daylight Savings Time Controls whether displayed time is daylight savings time or not. If set to "Yes" and the Optional Rule is empty, then the displayed time will be 1 hour ahead of normal time. · The "Automatic Daylight Saving Time Rule" has the following syntax: o start-time;end-time;saving. Both start-time and end-time have the same syntax: month, day, weekday, hour, minute o month: 1, 2, 3, . . , 12 (for Jan, Feb, . . , Dec) o day: [+|-]1, 2, 3, . . , 31 o weekday: 1, 2, 3, . . , 7 (for Mon, Tue, . . , Sun), or 0 indicating daylight savings rule is based on the day of the month. o hour: hour (0-23), o minute: minute (0-59) · If "weekday" is 0, it means the date to start or end daylight savings is the given date. · If "weekday" is not zero and "day" is positive, then daylight saving starts on the first "day" of the week (1st Sunday, 3rd Tuesday etc). [. . . ] HT496 User Manual Firmware 1. 0. 3. 86 Page 27 of 29 Last Updated: 7/2007 CONFIGURATION FILE DOWNLOAD The HT496 can be configured via Web GUI as well as through the Configuration File through TFTP or HTTP. "Config Server Path" is the TFTP or HTTP server path for configuration file. It needs to be set to a valid URL, either in FQDN or IP address format. The "Config Server Path" can be same or different from the "Firmware Server Path". [. . . ]