User manual GRUNDIG WT 2

[. . . ] WIRELESS TRANSMITTER WT2 DEUTSCH ENGLISH FRANÇAIS ITALIANO PORTUGUÊS ENGLISH WIRELESS TRANSMITTER WT2 __________ Package contents 1 2 3 4 5 6 7 8 9 10 11 WT2 WT2 installation kit (for attaching to television) Mains cable for indoor TV installation (e. g. Vision Company) Antenna cable 2 Stereo cinch cables I2C bus cables Operating manual Installation instructions for dealers The wireless transmission system WT2 communicates with the audio transmission receivers which are integrated in the FineArts LSP2/LSP3 or RS Set 2 active loudspeakers. A maximum of 4 active loudspeakers can be operated through the wireless module. Due to the wireless transmission, speaker connection cables are no longer necessary. I Volume Program Slider S-VHS Video in L Audio in R International and national regulations limit the audio transmission range to prevent radio interference. [. . . ] However, this is only the case if an automatic transmission search (ATS) has first been performed on the television. The loudspeakers must be switched off prior to starting installation. Please carefully observe the installation sequence, the television's menu directions show each next step to be performed. You can obtain information at any time about the required steps by pressing »?« (Help). 2 Select the line »Install front« with »P+« or »P-«, activate with »OK« and set to »Yes«; then confirm with »OK« (if you do not intend to install front loudspeakers, press »P+« or »P-« to select »No«). 3 Select the line »Install Surround« with »P+« or »P-«, activate with »OK« and set to »Yes«; then confirm with »OK« (if you do not intend to install surround loudspeakers, press »P+« or »P-« to select »No«). 4 Select the line »Start installation« with »P+« or »P-« and confirm with »OK«. ­ The status menu »Start installation« appears on the television screen. ­ The automatic installation procedure starts. 41 ENGLISH INSTALLATION (I2C) _____________________________________ 5 Turn on the left front loudspeaker with the mains switch. ­ The loudspeaker indicator flashes orange, after completion of the installation it flashes green. Note: If the loudspeaker indicator continuously illuminates orange when switched on, it has already been installed at FineArts Audion. In this case, briefly press »RESET« to set the loudspeaker to installation mode. »RESET« should not be pressed for longer than 5 seconds, as this will delete all installation data. ­ The loudspeaker indicator initially flashes orange, after completion of installation it flashes green. ­ The loudspeaker indicator initially flashes orange, after completion of installation it flashes green. ­ The loudspeaker indicator initially flashes orange, after completion of installation all four loudspeaker indicators continually illuminate green. ­ The message »Installation completed« appears on the television screen. ­ Sound is not transmitted until the system configuration has been set. Note: The installation can be prematurely interrupted by pressing »OK« on the remote control (»Installation abortted« appears). In this case, the loudspeaker installations successfully completed up until the interruption remain saved. Registering WT2 with the HiFi system FineArts Audion When you simultaneously operate WT2 with the HiFi system FineArts Audion, you must register the wireless module with the HiFi system. This procedure is described in the installation instructions from FineArts Audion. 42 INSTALLATION (I2C) _____________________________________ System configuration, e. g. for Lenaro The system configuration, which is automatically set up during installation, can be checked in the following ways: 1 Call up the television menu »EASY DIALOG« with »i«. 2 Select the menu »Installation« with »P+« or »P-« and activate with »OK«. [. . . ] more loudspeakers are not registered by the WT2. No audio playback although loudspeakers are already installed. Data communication is blocked. Disconnect the power cord from the WT2 and plug it in again after a short time. I2C only: using the power switch, switch off the television and switch it on again shortly afterwards. Disconnect the power cord from the WT2 and plug it in again after a short time. [. . . ]