Detailed instructions for use are in the User's Guide.
[. . . ] MODE
Used to select AUTO run, COOL, DRY, HEAT and FAN operation
AUTO
LO
MED
HI
ON/OFF
TEMP
10 12
14
FAN TIMER
21
15 16
SWING CLOCK
22
Used for unit start and stop.
17
SLEEP
23
15. HOUR 24
Used to set clock and timer setting.
18
LOCK RESET
17. HEAT
Used to select heat mode.
When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working.
NOTE: (1)The following functions are not available 4 12 24 and 26 (2) Cooling only unit do not have functions and displays related with heating.
Hints
After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. [. . . ] (Not Timer setting) Power indicator on indoor unit lights up.
Use COOL in summer.
Use HEAT in winter
Use DRY in spring, autumn and in damp climate.
(2) Select operation mode
Press MODE button. For each press, operation mode changes as follows:
ON/OFF TEMP
AUTO
COOL
DRY
HEAT
FAN
6 2 1 3 3
SET MODE
Unit will run in operation mode displayed on LCD. setting on LCD.
FAN
TIMER
4
SWING CLOCK
5
SLEEP
(4) Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
LOCK RESET
AUTO
LO
MED
HI
COOL operation starts when room temp. setting.
Ultra-low air flow
Unit runs at the speed displayed on LCD. setting, unit will run intermittently at LO speed regardless of FAN setting.
o
Temp. setting, unit will run in mild DRY mode.
Hints
On cooling only unit, heating mode is not available. When starting it next time, just press ON/OFF button and unit will run in previous status.
6
Operation
(5) Air flow direction adjustment
After operation mode is selected, vertical flap will open automatically according to the mode. COOL About 10
o
HEAT About 60o
Up and down (Use remote controller)
Left and right air flow adjustment Press SWING button, vertical flap will move within (manual)
the range shown in the Fig. Move the horizontal blade by a knob on air conditioner to adjust left and right direction referring to Fig.
About 10o COOL About 45o HEAT About 60o
Cautions:
It is advisable not to keep vertical flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur.
Cautions:
When humidity is high, condensate water might occur at air outlet if all horizontal louvers are adjusted to left or right.
(6) Unit stop
Press ON/OFF button. Vertical flap closes automatically.
Cautions:
Unit won't restart until 3 minutes have elapsed, due to system protection. HEAT mode is not available on cooling only unit.
Hints
As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more helpful for a better air circulation. As warm air flows upward in HEAT mode, adjusting air flow downward will be much more helpful for a better air circulation. It is harmful to your health in summer to go frequently in and out of places where temp. More than this, unit's load can be reduced and power consumption cut down as well. in COOL mode.
7
Operation
TIMER Operation
Set Clock correctly before starting Timer operation
You can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night.
TIMER ON/OFF
(1)After unit start, select your desired operation mode. Power indicator on indoor unit lights up.
(2)TIMER mode selection
Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows:
ON
TIMER ON
OFF
TIMER OFF
ON
OFF
blank
ON/OFF
TEMP
TIMER ON-OFF
MODE
Select your desired TIMER mode (TIMER ON or TIMER OFF) ON or OFF will flash.
1
SET
3
FAN
4
TIMER
(3)Timer setting
Press HOUR / button. It can be adjusted within 24 hours.
3
SWING
2
CLOCK
SLEEP
LOCK
RESET
(4)Confirming your setting
After setting correct time, press SET button to confirm, "ON" or "OFF" stops flashing Time displayed: Unit starts or stops at x hour x min. Timer mode indicator on indoor unit lights up.
To cancel TIMER mode
Just press TIMER button several times until TIMER mode disappears.
Hints
After replacing batteries or a power failure happens, Time setting should be reset. Remote controller possesses memory function, when use TIMER mode next time, just press SET button after mode selecting if timer setting is the same as previous one.
8
Operation
TIMER ON-OFF TIMER ON-OFF
(1)After unit start, select your desired operation mode Operation mode will be displayed on LCD. When the remote controller is manipulated, it gets the system back to the normal operation mode.
10
Operation
Comfortable SLEEP
Before going to bed at night, you can simply press the SLEEP button and unit will bring you a sound sleep in selected mode.
In COOL mode
One hour after SLEEP mode starts, temp. [. . . ] Cleaning of the air filter.
Once every two weeks
Proper temperature
Closing of doors and windows during operation
Effective use of the timer.
Curtains or blinds for windows
Avoid time-wasteful operation
Never fail to observe the followings
Do not sprinkle water over the unit. Do not block the inlet or outlet.
Do not pull power plug.
Do not use for other purposes.
Such as food preservation plant cultivation or animal breeding.
14
Trouble shooting
Before asking for service, check the following first.
Phenomenon The system does not restart immediately. Cause or check points When unit is stopped, it won't restart immediately until 3 minutes have elapsed to protect the system. When the electric plug is pulled out and reinserted, the protection circuit will work for 3 minutes to protect the air conditioner. [. . . ]