User manual HAIER TME1000
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HAIER TME1000. We hope that this HAIER TME1000 user guide will be useful to you.
Manual abstract: user guide HAIER TME1000
Detailed instructions for use are in the User's Guide.
[. . . ] is a registered trade mark of SKOPE Industries Limited.
TRADE MARK INFRINGEMENT
The SKOPE trade mark on this product is infringed if the owner, for the time being, does any of the following: · · · · Applies the trade mark to the product after their state, condition, get-up or packaging has been altered in any manner Alters, removes (including part removal) or obliterates (including part obliteration) the trade mark on the product Applies any other trade mark to the product Adds to the product any written material that is likely to damage the reputation of the trade mark Successors or assigns of the buyer Future owners of the product
Notice of the above contractual obligations passes to: · ·
i
TME650/1000
SKOPE One and Two Door Vertical Chillers
TABLE OF CONTENTS
1
1. 1 1. 2 1. 3 1. 4
INSTALLATION
Safety Information . 12
TME650/1000
SKOPE One and Two Door Vertical Chillers
ii
1
INSTALLATION 1. 1 Safety Information
When using any electrical appliance, safety precautions should always be observed. · When used by, or near, young children or infirm persons, close supervision is necessary. Young children should be supervised to ensure that they do not play with the appliance. [. . . ] Model TME1000 is rated at 4. 46A.
Important: For efficient operation of the cooler, it is essential that adequate ventilation be provided above the refrigeration unit.
TME650/1000
SKOPE One and Two Door Vertical Chillers
5
1
INSTALLATION 1. 3 Fitting the Sign Unit
For transit purposes the sign unit and sign side panels are packed inside the cabinet. Fit both the sign side panels over the four retaining screws on top of the cabinet. Slide the panels forward, flush with edges of the cabinet, and tighten the retaining screws. Clip the sign rear panel into the retaining slots on the rear of the sign side panels (see Figure 1 below). Lift the sign unit on to the top of the cabinet and connect the sign 3-pole plug into the roof top power supply socket. Clip the sign into the retaining slots on the front of each side panel and pull the sign unit firmly down. Ensure the two screws in the back of the sign unit fit into slots in the cabinet top angle bracket and then tighten all the screws. Turn the sign retaining clips on top of each side panel, to hold the sign unit firmly in position (see Figure 2 below).
Sign Retaining Clip Sign Side Panel
Sign Rear Panel Retaining Slot
Figure 1: Sign Rear Panel
Figure 2: Sign Retaining Clip
6
TME650/1000
SKOPE One and Two Door Vertical Chillers
1
INSTALLATION 1. 4 Fitting the Shelves
The chiller is supplied with five cabinet shelves, which may be positioned at different heights to suit various products. Depending on the model cabinet, each shelf is held in place with either four or six shelf clips, which engage in the shelf support strips. The support strips are marked with a `+' for easy location of shelf clips. Establish the desired position for the shelves and securely engage a shelf clip in each of the shelf support strips (see Figure 3 below). Sit the shelves onto the shelf support clips.
Loading Product
For even cooling and efficient operation, allow air space around packages etc. Do not allow products to overhang the front of the shelf as this could prevent the doors from shutting or cause glass breakage. Leave an airspace of at least 75mm (3") above product loaded on the top shelf.
Shelf Support Strip
Shelf
Shelf Clip `+' Mark
Figure 3: Shelf Clip
TME650/1000
SKOPE One and Two Door Vertical Chillers
7
2 OPERATION
2. 1 Cabinet Operation
Connect the cabinet to the mains power supply and check operation of the refrigeration unit and cabinet lighting. NOTE: After moving the chiller, allow the cabinet to stand for at least 30 minutes before connecting to the power supply.
Refrigeration Unit
The compressor, and evaporator and condenser fans should all operate continuously from the time the cabinet is plugged in. This may be verified by listening for compressor switch on and checking for air movement inside the cabinet. The compressor and condenser fans should switch off when the cabinet internal temperature reaches approximately 2°C. The internal cabinet air will continue to circulate at all times.
Lighting
The sign light and cabinet interior lights will go on when the cabinet is plugged in, and will stay on permanently. The fluorescent lights will require a period of time to stabilise following initial start up.
8
TME650/1000
SKOPE One and Two Door Vertical Chillers
3 MAINTENANCE
3. 1 Lighting
Cabinet Interior lights
Depending on the model cabinet, the chiller has either one or two interior side lights. Each side light houses a 35 Watt T5 fluorescent tube (Ø16mm x 1450mm), which may be replaced without removing shelves or product from the cabinet. [. . . ] Disconnect the sign plug from the electrical box socket and remove the sign unit from the cabinet. The condenser coil is now accessible for cleaning.
Condenser Coil Sign Plug Socket
Figure 7: Cleaning the Condenser Coil
TME650/1000
SKOPE One and Two Door Vertical Chillers
11
3 MAINTENANCE
3. 3 Advanced Servicing
Advanced servicing should be carried out by an authorised service agent. SKOPE Cyclone unit service instructions can be found on top of the refrigeration unit. More detailed service and spares information is available in the SKOPE TME650/1000 Service Manual (P/No. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HAIER TME1000
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HAIER TME1000 will begin.