User manual HARMAN KARDON AVR 3000

[. . . ] AVR 3000 Audio/Video Receiver OWNER'S MANUAL AVR 3000 ® Power for the Digital RevolutionTM Table of Contents 3 4 4 5 7 9 11 14 14 14 15 16 17 17 18 19 19 19 21 21 21 22 22 23 23 25 25 25 25 26 27 27 29 30 30 30 31 32 34 34 34 35 35 36 36 37 38 38 39 39 39 40 42 50 50 51 Introduction Safety Information Unpacking Front Panel Controls Front Panel Information Display Rear Panel Connections Remote Control Functions Installation and Connections Audio Equipment Connections Video Equipment Connections SCART A/V Connections System and Power Connections System Configuration Speaker Selection and Placement Settings to be Made With Each Input Used Input Setup Surround Setup Speaker Setup Adjustments for Other Inputs Making Settings independent of selected Input Delay Settings Night Mode Settings Output Level Adjustment Using EzSet Manual Output Level Adjustment Operation Basic Operation Source Selection Controls and Use of Headphones Surround Mode Chart Surround Mode Selection Digital Audio Playback Tape Recording Output Level Trim Adjustment 6-Channel Direct Input Memory Backup Tuner Operation RDS Operation Advanced Features Display Brightness Turn On Volume Level Semi OSD Settings Full-OSD Time Out Adjustment Programming the Remote Programming the Remote with Codes Macro Programming Programmed Device Function Volume Punch-Through Channel Control Punch-Through Transport Control Punch-Through Resetting the Remote Memory Function List Setup Code Tables Troubleshooting Guide Processor Reset Technical Specifications Declaration of Conformity We, Harman Consumer International 2, route de Tours 72500 Château-du-Loir, FRANCE declare in own responsibility, that the product described in this owner's manual is in compliance with technical standards: EN 55013/6. 1990 EN 55020/12. 1994 EN 60065:1993 EN 61000-3-2/4. 1995 Carsten Olesen Harman Kardon Europe A/S 10/00 Typographical Conventions In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used. EXAMPLE ­ (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack EXAMPLE ­ (OCR type) indicates a message that is visible on the front-panel information display 1 ­ (number in a square) indicates a specific front-panel control 0 ­ (number in a circle) indicates a rear-panel connection 0 ­ (number in an oval) indicates a button or indicator on the remote A ­ (letter in a square) indicates an indicator in the front-panel display 2 TABLE OF CONTENTS Introduction Thank you for choosing Harman Kardon!With the purchase of a Harman Kardon AVR 3000 you are about to begin many years of listening enjoyment. The AVR 3000 has been custom designed to provide all the excitement and detail of movie sound tracks and every nuance of musical selections. [. . . ] Hold the remote in front of you at arm's length, making sure not to cover the EzSet Sensor Microphone 7 at the top of the remote and aim it at the AVR 3000, not vertically (like you'd do with a microphone). Release the button when the Program/SPL Indicator 2 stops flashing and you hear the test noise from the front left speaker. At this point, the EzSet circuitry will take over, adjusting the output level of each channel so that when the process is complete all levels will be equal and at the set reference point. This process may take a few minutes, depending on the extent of adjustment required. During the adjustment you will see the location of the channel position being adjusted appear in both the on-screen display (if connected) and the Main Information Display Y, alternating with a readout of the output setting, relative to the reference volume level. As the adjustment proceeds, a few things will happen simultaneously: · The channel position being adjusted will flash in the Speaker/Channel Position Indicators Q. If the test noise is heard from a channel other than the one shown in the Indicator, there is an error in the speaker connections. If this is the case, press the Test Button 8 TWICE to stop the adjustment. Then, turn the unit off and verify that all speakers are connected to the proper Outputs DE. · When the front left channel is being set at the beginning of the process, EzSet will adjust the volume level, as shown by the indication of the FRONT L L E V alternating in the onscreen display (if connected) and the Main Information Display Y with the volume indication. During the adjustment, the test tone may seem to pulse, or click, as EzSet changes the level. · As the other channels are set, the channel name and the adjustment offset will appear in the on-screen display (if connected) and the Main Information Display Y. While the level is changing, the Program/SPL Indicator 2 will change colors to reflect the output level in relation to the reference. A red indication shows that the level is too high, while an amber indication shows that the level is too low. When the Indicator is green, the level is correct, and the test noise will move to the next channel. · While adjustments are being made, the red LED under the AVR Selector 5 will flash. After the test noise has circulated once through each channel, it will send the tone to the front left channel once again, to finally adjust its output level. Upon completion of the front left channel adjustment, the Program/SPL Indicator will flash green three times and then go out. Manual Output Level Adjustment Output levels may also be adjusted manually, either to set them to a specific level with an SPL meter, or to make fine tuning adjustments to the levels obtained using the EzSet remote. Manual output level adjustment is most easily done through the OUTPUT ADJUST menu (Figure 7). If you are already at the main menu, press the ¤ buttons D until the onscreen > cursor is next to the OUTPUT ADJUST line. If you are not at the main menu, press the OSD button L to bring up the MASTER MENU (Figure 1), and then press the ¤ buttons D three times so that the on-screen > cursor is next to the Output adjust line. [. . . ] The red LED under the Input Selector 4 will go out and the Program/SPL Indicator 2 will stop flashing and turn green. The Program/SPL Indicator 2 will remain green until the remote is reset. Note that this may take a while, depending on how many commands are in the memory and need to be erased. When the Program/SPL Indicator 2 goes out, the remote has been reset to the factory settings. PROGRAMMING THE REMOTE 39 Function List No. [. . . ]