User manual HARMAN KARDON PM635
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HARMAN KARDON PM635. We hope that this HARMAN KARDON PM635 user guide will be useful to you.
Manual abstract: user guide HARMAN KARDON PM635
Detailed instructions for use are in the User's Guide.
[. . . ] Whether the text appears in all uppercase or upper- and lowercase characters, performance and operation remain the same.
2 TABLE OF CONTENTS
Introduction
Thank you for choosing Harman Kardon!With the purchase of a Harman Kardon PM635 you are about to begin many years of listening enjoyment. The PM635 has the most extensive range of audio and video processing, control and connectivity options ever offered by Harman Kardon, enabling it to provide the best possible audio and video reproduction with any type of source material. Teaming advanced processing circuitry with proprietary technologies such as EzSet/EQ, the PM635 seamlessly integrates every component in your entertainment system to deliver the best possible sound and images. [. . . ] The settings will reset, and you may now continue to make any needed changes following the instructions shown below. Once you make the first change to the default settings, the setting on the DELAY RESET line will return to OFF, indicating that the factory defaults are no longer in effect. Now the cursor will be at the CEN line so that the delay for the center speaker may be set. Press the < / > Buttons EF until the distance from the main listening position to the center speaker is entered. Repeat the procedure for all active speaker positions by pressing the ¤ Button EF again and use the < / > Buttons EF to change the setting. If you have already run Ezset/EQ, return to the settings established by the automated system by pressing the //¤ Navigation Button EF until the cursor is pointing to the EZSET SETTINGS line. Next, press the </> Navigation Button EF so that O N is highlighted in reverse video. The settings will be resent to the values calculated by Ezset/EQ, and the menu will be locked so that the settings may not be changed. To go back into the menu and make any manual changes to one or more channels, you must first return the cursor to the EZSET SETTINGS line and press the </> Navigation Button EF so that OFF is highlighted in reverse video. When the delay time for all speaker positions has been set you may return to the master menu by pressing the //¤ Navigation Button EF until the cursor is pointing to BACK T O MANUAL SETUP and then pressing the Set Button FQ. Note that the delay settings may also be adjusted at any time when the Dolby Digital or Dolby Pro Logic II modes are in use by pressing the Delay button on the remote Z. In the MAN mode, the test tone will also start immediately, but the tone will only be moved to another channel by pressing the //¤ Navigation Button EF. When the manual sequencing mode is active, the tone is turned off by pressing the //¤ Navigation Button EF until the cursor is pointing to the TEST TONE line and the </> Navigation Button EF is then pressed to select OFF in the highlighted video. The final option for tone adjustment using the menu system is to not use the internal test tone at all. To do this, simply use the //¤ Navigation Button EF to change the channel and then use the //¤ Navigation Button EF to change the output level. When making channel output adjustments without the internal test tone we strongly recommend that you use a test disc in the "repeat" mode on your DVD or CD player so that the signal being used is constant throughout the adjustment process. NOTE: The subwoofer output level is not adjustable using the test tone. To change the subwoofer level, follow the steps for Output Level Trim Adjustment on page 46. When all channels have an equal volume level, the adjustment is complete. Now turn the Volume d down to about -40dB, otherwise the listening level may be too high as soon as the source's music starts to play. To exit this menu, press the //¤ buttons EF until the on-screen cursor is next to the BACK T O MANUAL SETUP line, and then press the Set Button FQ to return to the MANUAL
SETUP.
Figure 22 To provide the maximum flexibility, channel output level adjustments may be made either with or without the internal test tone, and when the tone is in use, it may be programmed to automatically circulate among the active channels or to only move from one channel to the next on your command. When the CHANNEL ADJUST menu appears, we recommend that you first run the test tone once in the automatic mode to verify that the speakers have been properly connected. [. . . ] · The remote's backlight will remain lit for approximately five seconds after the Light Button Q is pressed, and it will stay lit for another five seconds if any key is pressed while the backlight is on. You may keep the backlight lit by holding the Light Button, but extensive use of the backlight will reduce battery life. · The LCD display will remain on for ten seconds after a key is pressed and then turn off to conserve battery life. · When any button is held for more than thirty seconds the LCD will turn off and the remote will stop transmitting the codes to conserve battery life.
Figure 87
62 PROGRAMMING THE REMOTE
Troubleshooting Guide
SYMPTOM Unit does not function when Main Power Switch 1 is pushed CAUSE · No AC Power SOLUTION · Make certain AC power cord is plugged into a live outlet · Check to see if outlet is switch controlled · Make certain that all input and speaker connections are secure · Press Mute button gK · Turn up volume control · Follow the instructions in the Display Brightness section on page 47 so that the display is set to VFD FULL · Check speaker-wire connections for shorts at receiver and speaker ends · Contact your local Harman Kardon service depot ENGLISH
Display lights, but no sound or picture
· Intermittent input connections · Mute is on · Volume control is down
Units turns on, but Front-Panel Display does not light No sound from any speaker; light around Power switch 2 is red
· Display brightness is turned off
· Amplifier is in protection mode due to possible short · Amplifier is in protection mode due to internal problems · Incorrect surround mode · Input is mono · Incorrect configuration · Stereo or Mono program material
No sound from surround or center speakers
· Select a mode other than Stereo · There is no surround information from mono sources (except with Theater and Hall surround modes) · Check speaker mode configuration · Some surround modes may not create rear-channel information from nonencoded programs · Change remote batteries · Press the AVR Selector B · Make certain front-panel sensor is visible to remote or connect remote sensor · Move unit or antenna away from computers, fluorescent lights, motors or other electrical appliances · Resume play for DVD · Check that Digital Signal is fed to the Digital Input selected
Unit does not respond to remote commands
· Weak batteries in remote · Wrong device selected · Remote sensor ¯ is obscured
Intermittent buzzing in tuner
· Local interference
Letters flash in the Channel Indicator Display Ú and Digital Audio stops
· Digital audio feed paused
Processor Reset
In the rare case where the unit's operation or the displays seem abnormal, the cause may involve the erratic operation of the system's memory or microprocessor. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HARMAN KARDON PM635
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HARMAN KARDON PM635 will begin.