User manual HARMAN KARDON TD4800

[. . . ] The TD4800 has a wide range of features and options that accommodate virtually any combination of speakers, room size and program sources. It is as easy to operate as it is to set up, but in order to take maximum advantage of the many advanced technologies within your new AVR, it is strongly recommended that you take a few minutes to read this owner's manual. If you have any questions about this product, its installation or its operation, we recommend that you contact your dealer or installer, as they are your best source of local information. You may also access a wealth of information and assistance by visiting our Web site at www. harmankardon. com. [. . . ] Using the front left speaker as a reference, press the </> Navigation Button o to bring all speakers to the same volume level. When the </> Navigation Button o is pushed, the test noise circulation will pause on the channel being adjusted to give you time to make the adjustment. When you release the button, the circulation will resume after five seconds. Continue to adjust the individual channels until the volume level sounds the same from each speaker. Adjustments should be made with the </> Navigation Button o only, NOT the main volume controls. If you are using a sound-pressure level (SPL) meter for precise level adjustment, set the volume so that the meter reads 75dB, C-Weighting Slow. You may also make these same adjustments with complete manual control over the channel being adjusted by pressing the //¤ Navigation Button o until the cursor is pointing to the TEST TONE SEQ line on the menu and then using the </> Navigation Button o to select MANUAL in the highlighted video. In the MANUAL mode, the test tone will also start immediately, but the tone will only be moved to another channel by pressing the //¤ Navigation Button o. When the manual sequencing mode is active, the tone is turned off by pressing the //¤ Navigation Button o until the cursor is pointing to the TEST TONE line and the </> Navigation Button o is then pressed to select OFF in the highlighted video. The AVR's EzSet feature may also be used as an SPL meter to assist in accurate setting of the output levels, when either the internal test tone or an external source such as a test disc is used. Press and hold the SPL Select Button 45 on 49 47 43 the remote until the red LED 48 46 Set Button under the 44 42 q lights and the LCD screen in the remote 35 37 39 41 changes to the display shown in Figure 10. In addition, any of the settings made in the initial configuration of the unit may be changed at any time. As you add new or different sources or speakers, or if you wish to change a setting to better reflect your listening taste, simply follow the instructions for changing the settings for that parameter as shown in this section. Having completed the setup and configuration process for your TD4800, you are about to experience the finest in music and home theater listening. Enjoy! SYSTEM CONFIGURATION 29 OPERATION Basic Operation Once you have completed the initial setup and configuration of the TD4800, it is simple to operate and enjoy. The following instructions will help you maximize the enjoyment of your new receiver: Turning the TD4800 On or Off · When using the TD4800 for the first time, you must press the Main Power Switch A to turn the unit on. This places the unit in a Standby mode, as indicated by the amber illumination surrounding the Standby/On Switch 1. Once the unit is in Standby, you may begin a listening session by pressing the Standby/On Switch 1 on the front panel, or the Power On Button b or AVR Selector e on the remote. This will turn the unit on and return the AVR to the input source that was last used. The unit may also be turned on from Standby by pressing any of the Input Selector Buttons dXhç on the remote or the Input Source Selector Button 7 on the front panel. Whenever the AVR is turned on, you will see all of the front-panel indicators light up for a few seconds. This is normal, and it is part of the unit's power-on self test procedure. [. . . ] message will appear in the upper line of the remote's LCD screen as shown in Figure 78. It may take a few minutes for the reset process to take place, and the length of time will vary depending on how much customization and programming has taken place. Please be patient; as long as the message appears in the display the remote is functioning properly. RESETTING. . . Figure 81 Figure 78 4. When the remote has been totally reset and returned to the factory default condition, a REMOTE RESET COMPLETE message will appear (Figure 79) briefly, and then the remote will return to normal operation. REMOTE RESET COMPLETE · The remote has a built-in backlight that may be activated by pressing the Light Button P. [. . . ]