User manual HOTPOINT AQD1070D 497 EX

[. . . ] WASHER-DRYER This symbol reminds you to read this instruction manual. EN GB English, 1 F Français, 13 ES Español, 25 Contents Installation, 2-3 Unpacking and levelling Connecting the electricity and water supplies Technical data PT Português, 37 AR , 49 Care and maintenance, 4 Cutting off the water and electricity supplies Cleaning the machine Cleaning the detergent dispenser drawer Caring for your appliance drum Cleaning the pump Checking the water inlet hose Precautions and advice, 5 General safety Disposal Load balancing system Opening the porthole door manually AQUALTIS AQD1070D 497 Description of the machine, 6-7 Touch control panel How to run a wash cycle or a drying cycle, 8 Wash cycles and options, 9 Table of wash cycles Wash options Detergents and laundry, 10 Detergent Preparing the laundry Washing recommendations Trouble shooting, 11 Assistance, 12 1 Installation EN !This instruction manual should be kept in a safe place for future reference. If the Washerdryer is sold, given away or moved, please ensure the manual is kept with the machine, so that the new owner may benefit from the advice contained within it. [. . . ] WASH CYCLE PHASE icons: these illuminate to indicate the progress of the wash cycle (Wash – Rinse – Spin/ Drain – Drying ). START/PAUSE button with indicator light: when the green indicator light flashes slowly, press the button to start a wash To change the language, switch the machine on and off again; in the 30” time period after it has been switched off, press and hold the temperature +spin +delayed start buttons simultaneously for 5’’. A short sound alert will be emitted and the set language will flash on the display. Press the buttons next to the “ “ and “V” symbols to change the language. Use the button next to the “OK” symbol to confirm the language, which will be set after 2”. If no buttons are pressed, the language set previously will be displayed after 30”. 7 How to run a wash cycle or a drying cycle EN WARNING: before you use the Washer-dryer for the first time, run a wash cycle with detergent and no laundry, using the 90° cottons cycle without pre-wash. All the indicator lights will illuminate for 1 second and the text AQUALTIS will appear on the display; the indicator light corresponding to the button will then remain lit in a constant manner and the START/PAUSE indicator light will flash. A temperature and spin speed is set for each programme; these may be adjusted. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of wash cycles on the following page. Pull out the detergent dispenser drawer and pour the detergent into the relevant compartments as described in “Description of the machine”. Use the relevant buttons on the control panel: Modify the temperature and/or spin speed. The machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most recently-used settings if they are compatible with the selected cycle. The temperature can be decreased by pressing the button, until the cold wash “OFF” setting is reached. The spin speed may be progressively reduced by pressing the button, until it is completely excluded “OFF”. Exception: if the programme is selected, the temperature can be increased up to a value of 90°C. The first time the button is pressed, the machine will automatically select the maximum drying cycle which is compatible with the selected wash cycle. Subsequent presses will decrease the drying level and then the drying time, until the cycle is excluded completely (“OFF”). Drying may be set as follows: A - Based on a set time period: between 20 and 180 minutes. B- Based on the desired laundry dryness level: Iron: suitable for clothes which will need ironing afterwards. Cupboard: suitable for laundry which can be put back in a cupboard without being ironed. Extra: suitable for garments which need to be dried completely, such as sponges and bathrobes. [. . . ] to achieve optimum results , use liquid detergent and pretreat cuffs , collars and stains. Stubborn stains: it is wise to treat stubborn stains with solid soap before washing, and to use the Cottons with pre-wash cycle. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be solved easily using the following list. Possible causes / Solutions: • The appliance is not plugged into the socket fully, or not enough to make contact. [. . . ]