User manual HUGHES & KETTNER CLUB REVERB

[. . . ] BEDIENUNGSANLEITUNG MANUAL ENGLISH DEUTSCH illustrations CAUTION!230 V~ 100 V~ 117 V~ T 0, 5 A SB 1250 mA SB 1000 mA TO PREVENT THE RISK OF FIRE AND SHOCK HAZARD DON´T EXPOSE THIS APPLIANCE TO MOISTURE OR RAIN. power consumption 175 VA LEAVE ENOUGH SPACE FOR PROPER VENTILATION! Ser. No. FX-UNIT IN OUT LINE OUT PHONES LINE OUT LINE IN RED BOX INPUT ENGLISH DEUTSCH FOOTSWITCH FS-1 HOME Congratulations and thank you for choosing the HUGHES & KETTNER CLUB REVERB amp! A team of guitarists and technicians developed the ATTAX amps with a single purpose in mind: To provide you with sophisticated guitar sounds and practical features in an easyto-handle package. [. . . ] - When connecting peripheral devices, always pay close attention to their specifications. - Ensure you have the correct AC power rating available before you plug in the amp. If in doubt, ask the venue's sound technician or the custodian of the building you are rehearsing in. With the unit off and unplugged, use a soft damp cloth to clean the exterior surface of the CLUB REVERB. identical fuse. - One or several GAIN and MASTER controls may be turned all the way down. - Never overlook the possibility that the guitar cable may be damaged. - A short circuit in the speaker signal chain may have tripped an internal fuse. Make sure none of the connections are shorted out and have a qualified service technician replace the fuse (identical specifications are a must). 6. 3 The footswitch does not switch channels: - The footswitch is not connected to the CLUB REVERB. Use higher-quality cables or re-arrange the cables you are using to reduce interference to a minimum. - The grounding of the connected devices may be causing a ground loop. DO NOT SEVER THE GROUND OF THE CONNECTED DEVICES UNDER ANY CIRCUMSTANCES! 6. 0 TROUBLESHOOTING 6. 1 The CLUB REVERB will not switch on: - The amp is not getting any AC power. Replace the fuse with another Try plugging all devices into the same socket via an AC power distributor/power strip. If this doesn't eliminate the noise, you must ensure the connection is galvanically separated by routing the signal through a DI box. 6. 5 You have connected an FX processor to the LINE OUT jack and the signal is totally distorted, even when you have dialed in a clean sound. Reduce the processor`s input sensitivity ("INPUT" or "GAIN"). 6. 6 You have connected an FX processor to the LINE OUT jack of the CLUB REVERB and the signal's volume level is way too low. Turn it up. Output Power: 65 watts rms into 8 ohms Freqency response: 20 Hz - 30 kHz (into 8 ohms) Speaker: CELESTION RockDriver Junior, 12", 8 ohms General features: Voltage: 230 V~ (European model) 117 V~ (North American model) 100 V~ (Japanese model) Max. power consumption: 175 VA Mains Fuse: slo-blo 500 mA (230 V model) slo-blo 1000 mA (117 V model) slo-blo 1250 mA (100 V model) 7. 0 TECHNICAL DATA Preamp Section Preamp section: CLEAN + LEAD solid state channels INPUT: LINE OUT: LINE IN: -10 dBV/ 1 M ohm 0 dBV/ 1k ohm 0 dBV/ 47 k ohms Dimensions: (W x H x D) 464 x 480 x 265 mms 18" x 18. 9" x 10. 4" Weight: approx. 33 lbs. /approx. 15 kgs. Power amp section:: 'CURRENT FEEDBACK' solid state power amp Wir freuen uns, daß Du Dich für einen HUGHES & KETTNER CLUB REVERB entschieden hast! Ein Team aus Gitarristen und Technikern hat die Verstärker der ATTAX Series mit dem Ziel entwickelt, anspruchsvolle Gitarrensounds mit einfachster Bedienung und praxisgerechter Ausstattung zu kombinieren. Der CLUB REVERB ist das ideale Arbeitsgerät für anspruchsvolle Gitarristen, die amtliche Grundsounds in einem kompakten Amp fordern. Seine leistungsstarke Current Feedback Endstufe sorgt nicht nur für 65 Watt Leistung, sondern auch für offenen "Röhrencharakter". [. . . ] Diese sollte an der LINE OUT Buchse des Amps angeschlossen werden, da der Ausgangspegel hier masterunabhängig ist. Das Signal ist dann symmetrisch ausgeführt (= balanced) und mit einer Speakersimulation versehen. 5. 0 WARTUNG UND SERVICE Die Amps der ATTAX Serie sind wartungsfrei. Dennoch gibt es einige Grundregeln, deren Einhaltung die Lebensdauer Deines Amps enorm verlängern. : - Sorge immer für eine technisch einwandfreie Geräteperipherie! - Sorge stets für freie Luftzirkulation an die Kühlflächen Deines Amps (Rückseite Ampchassis). - Vermeide in jedem Fall starke mechanische Erschütterungen, extreme Hitze, das Eindringen von Staub und insbesondere Nässe. [. . . ]