User manual HUGHES & KETTNER CONTOUR

[. . . ] ConTour SeriesTM Manual 1. 0 English Important Safety Instructions Before connecting, read instructions Important Advice on Safety!Please read before use and keep for later use! Wichtige Sicherheitshinweise!Bitte vor Gebrauch lesen und für späteren Gebrauch aufbewahren! · · · · · · · · · · · · · · · · · · · · · · · · · · · · Read all of these instructions!The product may fall, causing serious damage to the product or to persons! [. . . ] Así se evitan daños en el aparato a causa de un rayo y golpes de tensión en la red de corriente alterna. Figura 1 Figura 2 · · · · · · · · · · · ConTour Series 1. 0 Table of Contents A 1 2 2. 1 2. 2 2. 3 2. 4 2. 5 2. 6 2. 7 2. 8 B 1 1. 1 1. 2 1. 3 1. 4 2 2. 1 2. 2 2. 3 2. 4 2. 5 3 3. 1 3. 2 3. 3 3. 4 3. 5 4 4. 1 4. 2 4. 3 C 1. 1 1. 2 1. 3 D E 1 2 2. 1 2. 2 Notes on Rigging Safety . . 5 Maintenance, Inspection and Repair of ConTour SeriesTM Rigging Hardware . 22: The rigging track in the lid 11 11 11 11 12 12 13 13 14 14 15 Fig. 32: CT 112 sans grille 15 15 15 15 16 16 16 16 17 18 5 A Notes on Rigging Safety Please read these instructions carefully before you begin setting up the system! 1 Warranty and Liability HK AUDIO® shall not be held responsible for damages due to improper use or non-compliance with the safety specifications for setup and operation. All warranty and liability claims for personal injury and property damages are excluded if attributable to one or several of the following: · non-compliance with operating manual instructions, voiding product liability and warranty claims · unintended use of rigging frames · non-compliance with operating manual instructions regarding transportation, storage, initial setup, operation, maintenance and repair · unauthorized structural modifications performed on rigging hardware · unauthorized modification of the parameters indicated in the operating manual · inadequate or improper repairs 2 Notes on Safety for the HK Audio® CT 112 and CT 115 The ConTour SeriesTM Rigging System's provisions for use require that it be installed in accordance with the following specifications. Before you begin installation, ensure that the pick points (for example, a chain hoist) on the stage roof or the venue's ceiling comply with BGV-C1 accident prevention regulations and that the safety standards authority TÜV has certified them for the full load. Prior to every installation, inspect all components to ensure they are in good working order, taking particular care to confirm that all Aeroquip tracks and connecting components (cables, fittings) are undamaged. Be sure to protect cabinets against rain and moisture when they are deployed outdoors. These enclosures must be mounted in accordance with the instructions stipulated in this installation manual. The principle requirement for safe handling and trouble-free operation of this rigging system is a thorough understanding of fundamental operating safety and safety regulations. This operating manual contains the most vital instructions concerning the safe operation of CT 112 and CT 115 enclosures. 2. 1 Responsibilities of the Operator As the operator, you are obligated to allow only those persons to work with rigging frames who are · 16 years of age or older, · physically and mentally able, familiar with the basic rules of industrial safety and accident prevention, and trained in the handling of rigging systems. Be sure to regularly review and confirm personnel's working safety awareness. In addition, task personnel with specific responsibilities for setting up, putting into service, operating, maintaining, and repairing equipment. Ensure that personnel are trained to work with the rigging system only under the supervision of a proficient and experienced technician. Ensure also that defects, flaws and other damage that could impede safety are repaired immediately. 2. 2 Maintenance, Inspection and Repair of HK AUDIO® ConTour SeriesTM Rigging Hardware Inspections § 39, VBG 9a of the German employers' liability insurance association's accident prevention regulations requires that load-bearing equipment be inspected by a qualified expert and possible defects be eliminated prior to initial commissioning by the recipient. § 40, VBG 9a requires that load-bearing equipment be inspected at least annually for cracks. When used in dynamic applications, equipment must be inspected for cracks every six months. Maintenance You are authorized to replace easily serviceable wearing or standard parts in accordance with the manufacturer's instructions. Repair In the event that parts of the load-bearing equipment have been deformed, it is up to the manufacturer to determine if they are repairable. [. . . ] This way the HK AUDIO® service team can immediately ascertain if an update is available for your product. · Use only original HK AUDIO® replacement speakers and parts!Most of these have been developed especially for HK AUDIO® products and are not available directly from speaker manufacturers!2. 2 The Drivers' Voice Coils Proceed as follows to replace the drivers' voice coils: · Remove the front grille as described above. [. . . ]