User manual ICOM 2200H
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ICOM 2200H. We hope that this ICOM 2200H user guide will be useful to you.
You may also download the following manuals related to this product:
ICOM 2200H 1 (30 ko)
Manual abstract: user guide ICOM 2200H
Detailed instructions for use are in the User's Guide.
[. . . ] INSTRUCTION MANUAL
VHF TRANSCEIVER
i2200H
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FOREWORD
Thank you for purchasing this Icom product. The IC-2200H VHF TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. [. . . ] to program.
· 3 beeps sound and the unit returns to VFO mode automatically.
VFO/CALL
MW
[Y]/[Z]
z Set the desired frequency in VFO mode. to program.
· 3 beeps sound and the unit returns to VFO mode automatically.
6
[EXAMPLE]: Programming 145. 120 MHz into the call channel via the microphone.
Push
MUTE NAR MID LOW
LOCK ANM DUP T-SCAN PRIO SCAN
to select VFO mode.
DIGITAL PRIO AO BUSY
Set the frequency.
DIGITAL PRIO AO BUSY MUTE NAR MID LOW
LOCK ANM DUP T-SCAN PRIO SCAN
Push
MUTE NAR MID LOW
LOCK
, then
momentarily.
DIGITAL PRIO AO BUSY
ANM
DUP
T-SCAN
PRIO
SCAN
SET
MONI
LOW
TONE
M/CALL
V/ MHz
SET
MONI
LOW
TONE
M/CALL
V/ MHz
SET
MONI
LOW
TONE
M/CALL
V/ MHz
Push
MUTE NAR MID LOW
LOCK
until large "C" appears.
DIGITAL PRIO AO BUSY
Push
MUTE NAR MID LOW
then
for 1 sec.
SCAN
DIGITAL PRIO AO BUSY
ANM
DUP
T-SCAN
PRIO
SCAN
LOCK
ANM
DUP
T-SCAN
PRIO
SET
MONI
LOW
TONE
M/CALL
V/ MHz
SET
MONI
LOW
TONE
M/CALL
V/ MHz
" "Beep " Beep " Beep "
DIGITAL PRIO AO BUSY MUTE NAR MID LOW
LOCK ANM DUP T-SCAN PRIO SCAN
SET
MONI
LOW
TONE
M/CALL
V/ MHz
36
7
SCAN OPERATION
I Scan types
Scanning searches for signals automatically and makes it easier to locate new stations for contact or listening purposes. There are 3 scan types and 4 resume conditions to suit your operating needs.
FULL SCAN (p. 38)
Band edge Scan Band edge
Repeatedly scans all frequencies over the entire band. Used as the simplest scan without any preliminary settings necessary.
PROGRAMMED SCAN
(p. 38)
Band edge Scan edges Band edge
Scan Jump Jump
Repeatedly scans between two user-programmed frequencies. Used for checking for frequencies within a specified range such as repeater output frequencies, etc. 38)
SKIP
M1 M0 M 199 M6 M5 M2 M3 M4
SKIP
Repeatedly scans memory channels except those set as skip channels. Used for oftencalled channels and for bypassing normally busy channels such as repeater frequencies.
SCAN RESUME CONDITION (p. Timer scan Pausing
4 resume conditions are available: 3 timer scans and pause scan. When receiving a signal, pause scan pauses until the signal disappears; timer scans pause for 5, 10 or 15 sec.
NOTE: A tone scan function is available to search for subaudible tones (e. g. when you want to find a subaudible tone frequency necessary to open a repeater). 37
SCAN OPERATION
7
I Scan start/stop
D Preparation
Scan resume condition (p. 41).
SCAN 2 SET B
z Push [VFO/LOCK] to select VFO mode for full/programmed scan; push [MR/CALL] to select memory mode for memory scan.
· Push [BANK/OPTION] to select a bank for bank scan.
D Operation
q Select VFO mode for full/programmed scan with [V/MHz SCAN ]; or memory mode for memory scan with [M/CALL PRIO ].
· Select the desired bank with [BANK OPT ] for bank scan.
x Set the squelch to the point where noise is just muted. c Push [SCAN 2(T-SCAN)] to start the scan.
Y Z · Push [Y] or [Z] for 1 sec. also starts the scan.
7
w Set the squelch to the point where noise is just muted. to start the scan.
· To change the scanning direction, rotate [DIAL]. · The memory channel readout blinks the scan type as follows:
v Push [SET B(D-OFF)] to switch full and programmed scan (P1, P2 and P3). b To stop the scan push [SCAN 2(T-SCAN)] or [CLR A(MW)].
r Push [SET LOCK ] to switch full and programmed scan (P1, P2 and P3). t To stop the scan, push [SET LOCK ] or [V/MHz SCAN ].
· During full scan
DIGITAL PRIO AO BUSY MUTE NAR MID LOW
LOCK ANM DUP T-SCAN PRIO SCAN
· During programmed scan
DIGITAL PRIO AO BUSY MUTE NAR MID LOW
LOCK ANM DUP T-SCAN PRIO SCAN
· During memory scan
DIGITAL PRIO AO BUSY MUTE NAR MID LOW
LOCK ANM DUP T-SCAN PRIO SCAN
· During Bank scan
DIGITAL PRIO AO BUSY MUTE NAR MID LOW
LOCK ANM DUP T-SCAN PRIO SCAN
SET
MONI
LOW
TONE
M/CALL
V/ MHz
SET
MONI
LOW
TONE
M/CALL
V/ MHz
SET
MONI
LOW
TONE
M/CALL
V/ MHz
SET
MONI
LOW
TONE
M/CALL
V/ MHz
( SET ) to select full, Push band* (A1, AA) or programmed scan (P1, P2 and P3) in sequence. (*Depends on versions) A1 : FM band (136174 MHz) AA : AM band (118136 MHz)
LOCK
Indicates scan edge channels. · P1 stands for 1A/1b · P1 to P3 are available when they are programmed, and ( SET ) . [. . . ] · Blown fuse.
I Troubleshooting
PROBLEM
No power comes on.
SOLUTION
REF.
· Check the connector pins. · A selective call or squelch function is activated such as pocket beep or tone squelch.
Sensitivity is low and only · Antenna feedline or the antenna connector solder · Check, and if necessary, replace the feedline or sol- p. 14 No contact possible with · The other station is using tone squelch. 44
Repeater cannot be ac- · Wrong offset frequency is programmed. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM 2200H
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM 2200H will begin.