User manual ICOM IC-3SA
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ICOM IC-3SA. We hope that this ICOM IC-3SA user guide will be useful to you.
Manual abstract: user guide ICOM IC-3SA
Detailed instructions for use are in the User's Guide.
[. . . ] During mobile operation, D O N O T operate the transceiver without running the vehicle's engine. When transceiver power is ON and your vehicle's engine is OFF, the vehicle's battery will soon become exhausted. This will avoid possible damage to the transceiver by ignition voltage spikes. During maritime mobile operation, keep the transceiver and microphone as far away as possible from the magnetic navigation compass to prevent erroneous indications. [. . . ] When selecting this condition, the tuner can be used at poor SWR's. In this case, automatic tuning in the HF bands activates only when exceeding SWR 3:1. Therefore, manual tuning is necessary each time you change the frequency. Although termed "through inhibit, " the tuner will be "through" if the SWR is higher than 3:1 after tuning.
CONVENIENT
Lights to indicate the AT-180 is turned ON.
· For the 50 MHz band: Push and hold [TUNER] to tune the antenna. If the [TUNER] light flashes slowly while transmitting, push and hold [TUNER] again to re-tune the antenna.
[TUNER/CALL]
· T u n e r s e n s i t i v e c o n d i t i o n (HF bands only) If you require critical tuning at any time during transmission, select the tuner sensitive condition. · A u t o m a t i c t u n e r s t a r t (HF bands only) If you want to turn OFF the tuner under conditions of VSWR 1. 5:1 or less, use "automatic tuner on" and turn the tuner OFF. 54 for turning the function ON and OFF.
Flashes to indicate re-tuning is necessary.
27
RECEIVE AND TRANSMIT
4
D Optional AH-4
AUTOMATIC ANTENNA TUNER
operation
The AH-4 matches the IC-3SA to a long wire antenna more than 7 m/23 ft long (3. 5 MHz and above).
· See p. · See the AH-4 instruction manual for AH-4 installation and antenna connection details. AH-4 setting example: For mobile operation Optional AH-2b antenna element
AH-4 operation Tuning is required for each frequency. B e s u r e to re-tune the antenna before transmitting when you change the frequency--even slightly.
Set the desired frequency in an HF band.
· The AH-4 will not operate on frequencies outside of ham bands.
USB
Push and hold [TUNER] for 2 sec.
For outdoor operation Long wire · The [TUNER] light flashes and "CW" appears while tuning.
Push [TUNER] for 2 sec.
W RW A R N I N G : H I G H V O L T A G E !
N E V E R touch the antenna element while tuning or transmitting.
CW
The [TUNER] light lights constantly when tuning is
N E V E R operate the AH-4 without an antenna wire. Note that the AH-4 cannot tune when using a 1 /2 long wire or multiple of the operating frequency. 49 for setting details and available frequencies.
Rotate the main dial to set a subaudible tone frequency. (in the M1 display) to activate the split frequency function (duplex function) with the pre-selected offset.
·When a subaudible tone frequency is selected in e, "FM-T" is selected simultaneously.
Q6 RPTR TONE
FM T
SPL
t Push and hold [PTT] to transmit; release [PTT] to receive. ·Push and hold [(F-3)TON] in the M4 display while pushing [PTT] to send the 1750 Hz tone burst. 32)
S1 PO
3
5
7
9 5
20
40
60dB 10
VFO A CH
M4 VOX DUP TON
y To check the repeater input frequency (direct signal from the other station), push and hold [(F-3)XFC] in the M1 display. N O T E : The split function may not be turned off when you change the operating band, push [(F-1)SPL] again to turn off the split function after you finish the repeater operation.
PROGRAMMING DUPLEX SHIFT FREQUENCY Push [POWER] to turn power OFF. While pushing [LOCK], push [POWER] to turn Select "DUP
power ON and enter initial set mode. 144M" using [MENU] or the [UP]/[DN] keys, then rotate the main dial to select the desired duplex offset.
CONVENIENT
Each memory channel can store a tone frequency and an offset frequency, as well as the operating frequency. Store repeater information into memory channels for quick and easy access to repeaters.
· The duplex offset can be selected from 4000 kHz to +4000 kHz.
17 DUP 144M
30
4
RECEIVE AND TRANSMIT
I Tone squelch operation
Tone squelch operation is a method of communications using selective calling. Before communicating using tone squelch, all members of your party must agree on the tone squelch frequency to use.
Push [MODE] one or more times to select FM Push and hold [DISPLAY] to enter Quick Set mode. mode.
Rotate the main dial to select the desired subaudible tone frequency.
·Available tone frequencies are the same as for repeater tone operation (see previous page).
· [Y]/[Z] or [M-CH] can also be used.
Set the tone frequency (quick set mode). 49 for setting details and available frequencies.
Q7 TONE SQL
FM TSQL SPL
Select M4 and turn the tone squelch function ON.
Push [(F-3)TON] to toggle tone squelch operation ON and OFF.
·When tone squelch is turned ON, "TSQL" appears in the display.
S1 PO 3 5 7 9 5 20 40 60dB 10
VFO A CH
Communicate in the usual manner.
· Push [PTT] to transmit; release to receive.
M4 VOX DUP TON
I Tone scan operation
By monitoring a signal that is being transmitted on a repeater input frequency, you can determine the tone frequency necessary to open a repeater.
During tone squelch or repeater operation, push
and hold [DISPLAY] to enter Quick Set mode. [. . . ] of memory pads Power ON check function Auto tune start function PTT tune function Packet data speed ACC output selection Speech synthesizer lang. Speech synthesizer speed Speech synthesizer S-meter CI-V address assignment Data transfer rate CI-V transceive CI-V 731
Initial set mode
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
Y
Z
37 CI-V 731
MENU
19 1TOUCH RPTR
67
MENU GUIDE
14
S1 M1 SPL A/B A=B XFC (when split is ON) V/M
(in memory mode)
MW SCN
MPW PRI SEL 50 NR
MPR V/M
(in memory mode)
S2
DISPLAY MENU
M2
MENU
MW
MÜV MCL NB COM BRK
S3 S4
7 ANF
144 NRL
M3 M4
MODE
FIL VOX 1/4 1/4 VOX
MET
DISPLAY
AGC AGC AGC
(SSB/AM) (CW) (RTTY) (FM)
M4 M4 M4
G1
DISPLAY MENU
BAND scope IF SHIFT TX freq. Memory name
G2 G3 G4
COM
TON
DISPLAY
DISPLAY
For 2 sec. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-3SA
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-3SA will begin.