User manual KENMORE 625.385560
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KENMORE 625.385560. We hope that this KENMORE 625.385560 user guide will be useful to you.
Manual abstract: user guide KENMORE 625.385560
Detailed instructions for use are in the User's Guide.
[. . . ] OWNER'S MANUAL
E
L
I
T
E
Reverse Osmosis System
MODEL NO. 625. 385560 UltraFilter 650
Caution: Read and follow all safety rules and operating instructions before first use of this product.
Questions ?Visit www. KenmoreWater. com or call toll free 1-800-426-9345 (M - F, 7AM - 8 PM CST)
Repair or Parts ?Call toll free 1-800-366-7278 See back cover for other Sears service numbers. [. . . ] Continue pushing until the tube bottoms out against the back of the fitting. When a 1/4" tube is fully engaged, 11/16" of the tube has entered the fitting. When a 3/8" tube is fully engaged, 3/4" of the tube has entered the fitting. If using tubing other than tubing supplied with the system, be sure it is of high quality, exact size and roundness with a smooth surface. See Figure 20.
Push In Fitting Tube
Cut tubing square with end of tubing round, smooth, with no cuts, nicks or flat spots.
Tube Correctly Cut
Figure 16
O-Ring Collet
Tube Partially Engaged With Fitting
Figure 17
O-Ring Collet
Tube Fully Engaged With Fitting
Figure 18
Collet (Depress to Remove Tubing) Fitting O-Ring Seal Collet
Tubing
Collet and O-Ring
Disconnect Tubing
Figure 20
Figure 19
Questions?Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater. com
14
Step 6 - Connect Tubes
3/8" black tubing
1/4" red tubing water supply fitting 3/8" blue tubing
NOTE: Tubing lengths should allow access to the back of the assembly for servicing. NOTE: Codes in the state of Massachusetts require installation by a licensed plumber and do not permit the use of saddle valves. If you live in the state of Massachusetts, review plumbing code 248-CMR of the Commonwealth of Massachusetts before proceeding with the installation.
HOT
COLD
sink p-trap
1/4" green tubing
3/8" yellow tubing
tubing connector
Tube Connections
Figure 21 CONNECT YELLOW TUBE TO STORAGE TANK
1. Run the other end of the yellow tube to the fitting on top of the storage tank. This will occur in the sanitizing step.
CONNECT BLUE TUBE TO REVERSE OSMOSIS ASSEMBLY
The blue tube connection was completed in the faucet assembly steps.
CONNECT BLACK TUBE FROM REVERSE OSMOSIS FAUCET TO DRAIN ADAPTER
1. The other end needs to be attached to the black collet on the sink drain adapter. Cut this tube as needed to route in as straight of a run as possible, without loops, dips, low spots or kinks. Pull on the tube to be sure it is held firmly in the fitting.
CONNECT GREEN TUBE TO COLD WATER SUPPLY PIPE
1. Run one end of the 1/4" green tube to the fitting on the water supply pipe. This is a compression fitting.
CONNECT RED TUBE TO REVERSE OSMOSIS FAUCET
The red tube connection was completed in the faucet assembly steps.
Questions?Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater. com
15
Step 7 - Sanitize, Test and Purge System
SANITIZE THE SYSTEM
Sanitizing is recommended immediately after installation of the Reverse Osmosis system. It is important that the person installing or servicing the system have clean hands while handling inner parts of the system. Locate the eyedropper that is included in package and common household bleach (5. 25%). Handle bleach according to bleach manufacturer's recommendations. Sanitizing the system will be completed during the pressure test and purging steps on the following page. NOTE: The bleach must be removed from the system before drinking the water. Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater. com
16
Step 7 - Sanitize, Test and Purge System
PRESSURE TEST THE SYSTEM
NOTE: Complete the sanitizing procedures on the preceding page before pressure testing. [. . . ] If rate does not increase, replace the postfilter cartridge and Reverse Osmosis membrane cartridge. See page 20.
Problem: System makes lower amount of product water than usual.
Cause: Storage tank air-charge less than 5-7 psi. Correction: Open Reverse Osmosis faucet and drain tank until flow slows to a drip. Close faucet to refill the tank.
Problem: High total dissolved solids (TDS) in product water
Cause: Water supply to the Reverse Osmosis sys- Correction: tem not within specifications. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KENMORE 625.385560
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KENMORE 625.385560 will begin.