User manual LIFT-MASTER HL410

[. . . ] Strong winds will greatly affect the efficiency of this operator on these types of gates. IMPORTANT NOTE The gate must be level and operate smoothly and freely. If it does not, damage to the operator may result and the life expectancy will be greatly reduced. Doc 01-20230 Rev B 6 Safety Information Safety Information Automatic gate operators provide convenience and security to their users. However, because these machines can produce high levels of force, it is important that all installers and users be aware oft he potential hazards associated with improperly installed or adjusted units. [. . . ] The operator must be level. 2 The two brackets should be welded to the gate and the post as shown. They can be welded directly or modified to suit your particular application. FOR MODEL HL410-21 Dimension A 5" to 5-1/2" 4-1/2"to 5" 4"to 4-1/2" 3-1/2"to 4" Gate Opening 90° 100° 110° 120° Do not weld brackets with operator attached. Avoid nicks. MODEL HL410-21 Front Mounting Bracket (shortest) Hinge Point 10. 60 A 5" 3" to 3 1/2" MODEL HL410L-21 - 90° OPENING Hinge Point 32 1/2" Open 4. 68 47. 81 3. 90 Rear Mounting Bracket (longest) Both Brackets In Line Gate shown in the Left-Hand Closed Position 01-20230F5 Figure 3 Doc 01-20230 Rev B Installation Step 3: 11 Optional Mounting OUTWARD SWING WARNING Do not install outward swing gates in applications where gates will swing into public area. Use outward swing gates only in applications where the gate will open into secure area and where the person operating the gate has control of traffic in the path of the gate. Do not use the "Open Only" mode of the controller for an outward swing gate installation. Gate stops must be used at both the full open and close positions (see Step 1). The difference being that the rear mounting point is 5" to the right of the hinge point instead of 5" to the left as shown in Step 2 (distance between mounting points is 27-1/2" instead of 371/2"). The piston rod should be fully retracted when the gate is in the closed position. The unit should be mounted with the gate in the closed position (see Step 4). Follow wiring for outward swing. LARGE PILLARS OR WALLS If the dimension from the centerline of the gate to the outer edge of the pillar or wall is 3-3/4" or less, you can notch out part of the pillar or wall (see Example A ­ Figure 4) as shown. If this dimension is larger than 3-3/4", then it will be necessary to notch out larger portion (see Example B ­ Figure 4) large enough to house the unit. Contact a LiftMaster dealer if your application does not fit these guidelines. OPTIONAL MOUNTING - NOTCH AS REQUIRED 01-20230F6 EXAMPLE A EXAMPLE B Figure 4 Doc 01-20230 Rev B 12 Installation Step 4: 1 2 Mounting Manually open the gate and attach the unit to the two (2) mounting brackets (see Figure 5 below). Manually open and close the gate a few times to ensure the mounting brackets and gate stops are positioned properly with no interference (the unit is shipped in the disconnect position to allow for this). Mount the controller in a convenient location, within reach of the unit's 4 ft. Make sure the cord is not stretched taut (it should have a slight amount of slack during the full cycle). Refer to the electrical diagram attached to the inside of the controller door for accessory wiring. Please install all safety devices necessary to make this installation as safe as possible. Control Wiring Terminal Strip 1 2 4 5 6 8 9 10 D1 D1 D2 D2 24 VAC. OPEN/CLOSE If the gate is closed, when activated, it will open. If the unit is activated for open only, it must be used in conjunction with the Stop feature, or a hazardous and dangerous condition may be present. You will also need the optional automatic close timer. Radio Control to Open / Close STOP A device such as a reversing edge, loop detector, or photo beam can be used as a Stop device. It must have a normally closed contact. Reversing Device Used as Stop Reversing Device Will reverse both directions 4 5 Norm. open "only" Reversing Device 4 2 Normally Closed If used, remove jumper 2 to 4 Loop Detector to Open Only 6 9 10 5 4 RED BLK GREY GREY If used, leave jumper 6 to 7 in 8 Loop Detector to Reverse while closing If used, remove jumper 6 to 7 IT IS RECOMMENDED THAT IF A OPEN ONLY IS USED, A STOP BE USED WITH IT . . Open Only Stop 45 GRN WHITE 7 8 9 10 1 2 3 7 8 9 10 1 PURP RED RED YEL ORG 2 4 If used, remove jumper 2 to 4 RED 14 9 10 D1 D1 RED 4 6 7 8 9 10 D2 D2 0 1 -2 0 2 3 8 F7 Slave Unit Auto. [. . . ] In case of failure due to deficiencies in material or workmanship during the warranty period, the completer gate operator will be repaired or replaced at the manufacturer's option. Replacement parts are warranted for the remaining portion of the original warrant period. LiftMaster will pay freight on our return of repaired or replaced items in warranty. This warranty gives you specific rights, and you may also have other rights which vary form state to state. Doc 01-20230 Rev B 20 Parts List Parts List Hatch Kit MG49258 Mounting Pin Kit MG49136 End Cap MG49196 Disconnect Hex Key MG5100812 Mounting Clip MG5100816 Drive Unit Rod Cover MG5100813 Power Cord MG24719 C-Clip Kit MG49136 Rear Mounting Bracket MG5100815 Front Mounting Bracket MG5100814 Connector Kit MG49133 Capacitor MG3101962 Main Circuit Board MG49070 or MG49110 Micro Circuit Board MG49071 OR MG49111 Fuse Kit MG49135 Relay MG3101963 Fuse Kit MG49135 Circuit Bd. [. . . ]