User manual LIFT-MASTER MADCBB

[. . . ] 845 Larch Avenue Elmhurst, Illinois 60126-1196 www. liftmaster. com radio receiv d now include NEW!er Optional full length aluminum tower Models: MADCBB, MATDCBB, MASDCBB & MASTDCBB (MEGA ARM, TOWER, MEGA SPRINT & MEGA SPRINT TOWER) 1/2 HP COMMERCIAL DUTY PARKING GATE OPERATOR INSTALLATION AND SERVICE MANUAL IMPORTANT: Read and understand Warranty Page first. Batteries (not included) MUST be connected for proper operation of unit. Use (2) LiftMaster sealed 12VDC 7AH (Part # MBAT). TA B L E O F C O N T E N T S INTRODUCTION Unit Overview . . 10 SUGGESTED ENTRAPMENT PROTECTION DEVICE LOCATIONS Free Exit Operation . [. . . ] Use safety loops, stop loops, photo beams and a long enough time delay. ) NOTE: Can be used with multiple vehicle memory buffer to allow gate to close and reset count memory to zero. When using clutch option, turning on S1-6 & S2-7, gate will close by timer whenever forced up. SWITCH 8 - AUTO OPEN ON POWER FAILURE: When switch number 8 is in the ON position, the operator will automatically open the gate approximately 15 seconds after the loss of power. Once power is restored the operator will resume normal operation after the first car passes closing loop or if close timer S2-7 in turned on (it is recommended to allow the gate to close by loop, not by timer). Seconds - - 1 - - 2 - - 4 - - 8 - - 16 S2 ON Shows Default Settings 12345678 Close Timer 1-5 Mode Selection 6-8 7 WARNING T A L L T H E R E C E I V E R INS WARNING To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: · ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. · Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. · ALWAYS keep gate or garage door in sight until completely closed NEVER permit anyone to cross path of moving gate or door. NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. AVERTISSEMENT 1 2 3 4 5 6 7 8 9 10 11 J5 WIRING THE RECEIVER AVERTISSEMENT Contacts 1 and 2 on the receiver terminal strip are for power. Connect terminals 1 and 2 to the accessory power terminals on the S4 terminal strip at the bottom of the logic board (Figure 1). Contacts 3 and 4 on the receiver terminal strip are for a common and a relay. Connect terminals 3 and 4 to terminals 1 and 10 on the S5 terminal strip at the top of the logic board. J4 BAT­ BAT SET SECURITY MODE The Universal Receiver can be used with up to 15 rolling code remotes or passwords in HIGH security mode. Alternately, it can be used with up to 31 of any type remote in NORMAL security mode, including any combination of rolling code, billion code, or dip switch remotes. The jumper must be set at the HIGH position for the receiver to operate in HIGH security mode. It must be set at NORMAL position to operate at the NORMAL mode (Figure 2). When changing from NORMAL to HIGH security mode, any previous remote codes must be erased. Repeat Steps 2 and 3 in the Programming Section below to reprogram the receiver for each remote control in use. The receiver is factory set at HIGH. ACC+ ACC­ BAT­ BAT+ Jumper P1 to J4 Accessory Power Jumper P2 to J4 Accessory Power Jumper P3 to J5 Terminal 1 Jumper P4 to J5 Terminal 10 1 10 1 + ­ 4 2 3 FIGURE 1 Security Mode Terminals Jumper Security Mode Terminals Jumper PROGRAMMING THE REMOTE TO THE RECEIVER STEP 1: Pry open the front panel of receiver case with a coin or a screwdriver. STEP 2: Press and release the "learn" button on the receiver. STEP 3: Within 30 seconds, press and hold the button on the hand-held remote that you wish to operate your gate. The opener will now operate when the push button on either the receiver or the remote control is pressed. Repeat Steps 2 and 3 for each remote control that will be used to operate the gate. HIGH SECURITY MODE FIGURE 2 OPENING RECEIVER Connect Antenna C P2 M Output Duration Terminals Security Mode Power Supply Jumper OPEN RECEIVER Indicator Light Learn Button NORMAL SECURITY MODE 24V 12V TO ERASE ALL REMOTE CONTROL CODES Press and hold the "learn" button on the receiver panel until the indicator light turns off (about 6 seconds). Then follow the steps above to reprogram each remote control. FIGURE 3 (Not Provided) 8 HIGH NORM ADJUSTMENTS WARNING To reduce the risk of SERIOUS INJURY or DEATH: · Disconnect power BEFORE performing ANY adjustments near drive shaft. WARNING WARNING GATE ARM INSTALLATION AND LEVELING Install arm in gate arm bracket by lining up holes in arm with the slotted holes in bracket. [. . . ] of each gate to the SHADOW LOOP J5 #8 input and common of the other (Figure 2). (Leave S1-6 and 8 OFF to allow relay to stay latched. ) FIGURE 1 Mega Arm K1 Relay C Open Input NO Other Operator (Slide, Swing, Teeth, etc. ) J5 #11 Access Device J5 #1 J5 #12 J5 #8 C NC Extra Open Limit Switch S1, #6 and #8 (ON) = K1 Relay PULSE only. S1, #6 and #8 (OFF) = K1 Relay LATCH only. FIGURE 2 Mega Arm K1 Relay Visitor Lane Tele-Entry J5 #1 J5 #9 J5 #1 J5 #9 K1 Relay J5 #11 J5 #8 C NO C NO J5 #11 J5 #8 Reader, etc. Resident Lane Mega Arm 12 C O N T R O L B O A R D L AY O U T OPEN GATE INPUTS-READER, PUSH BUTTON AUX OPEN / RESET (PULSE OPEN/CLOSE) SAFETY LOOP INPUT CLOSE GATE INPUT-CLOSE LOOP BACK AWAY-FREE EXIT LOOP EXTERNAL LIMIT INPUTS OBSTRUCTION SIGNAL CONNECTION D13 TX 1 2 3 4 5 6 7 8 9 SHADOW LOOP COMMONS - 0VDC 10 11 12 MANUAL OPEN S3 J5 J2 J3 D15 D16 D17 D18 D19 D22 D23 CLOSE S1 12345678 S2 12345678 D7 OPEN LIMIT SENSOR D6 OPEN DRIVERS ON D5 MOTOR BRAKE ON D4 CLOSE DRIVERS ON D3 CLOSE LIMIT SENSOR D2 OBSTRUCTION SENSE (IRD AND MRT) CPU JP2 OVER DRIVE CPU U5 U3 BATTERY CHARGE I/O INTERFACE PORT IRD1 R63 F1 1 AMP DC RELAY INDICATOR D1 RELAY (OPTIONAL) K1 H BEAT D11 J4 J1 AC BATTERY POWER LOW D14 F4 F3 15 10 WARNING FOR CONTINUOUS PROTECTION AGAINST FIRE REPLACE ONLY WITH THE SAME TYPE AND RATING OF FUSE D12 C NC NO DC K1 RELAY TERMINALS ACC+ ACC­ BAT­ BLK BAT+ RED 24V AC XFMR YEL YEL MOTOR BLU ORG 24VDC {REQULATED} INPUT LOCATIONS Accessory power is 24VDC regulated rated at 500 ma. [. . . ]