User manual MARANTZ WB4001T
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MARANTZ WB4001T. We hope that this MARANTZ WB4001T user guide will be useful to you.
Manual abstract: user guide MARANTZ WB4001T
Detailed instructions for use are in the User's Guide.
[. . . ] SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY. PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. [. . . ] Make sure that none of these parts are missing before beginning installation. If there are parts missing stop the installation and contact Marantz.
Wall plate (Qty 2)
GriplatesTM (Qty 8)
Mounting brackets (Qty 2)
5/16" x 3" Lag Bolts (wooden studs only) (Qty 8)
M4 x 20mm Phillips Head Screws (Qty 8)
5/16" Flat Washers (Qty 8)
M6 x 12 Safety knobs (Qty 2)
Template (Qty 1)
1. 1
Installation Tools
Soft Material/ Blanket Drill Gun 5/16" Socket Wrench Pencil
Phillips Head Screw Driver Tape Measure Level (Supplied)
-4-
2. 0
FINDING THE CENTER OF THE DISPLAY
WARNING: PROPER INSTALLATION PROCEDURE BY QUALIFIED PERSONNEL AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. WARNING: INVERT THE FLAT PANEL, PLACE IT ON A SOFT, FLAT SUFRACE TO PREVENT DAMAGE TO THE FLAT PANEL. DO NOT LAY THE FLAT PANEL ON THE FLOOR WITHOUT ANY PROTECTION TO THE GLASS. AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL.
Step 1
Once the flat panel is inverted, use a measuring tape to find the center of your flat panel measuring from outside to outside of the chassis (Figure 1).
Top of flat panel
Step 2
Using a pencil lightly mark the center of your flat panel (Figure 2).
Mark the center of the flat panel
Inverted flat panel
Measuring tape
C L
Bottom of flat panel Inverted flat panel
C L
Figure 2
Figure 1
-5-
3. 0
POSITIONING THE MOUNTING BRACKETS
Step 4
Step 3
Lay the mounting brackets (stamped arrows Match the center of viewing guide with the center facing out) Figure 3. line you marked in Step 1 (Figure 4).
Mounting brackets
Bottom of flat panel
Align the mounting brackets
C L
Arrows facing out
Bottom of flat panel
Figure 3
Figure 4
Step 5
The mounting brackets are designed with a center of viewing guide on the side of them (Figure 5).
Mounting bracket
Bottom of flat panel
Center of viewing guide
Figure 5
-6-
4. 0
SECURING THE MOUNTING BRACKETS
Step 7
Once the mounting brackets are aligned, secure the GriplateTM to the flat panel. NOTE: The dimples of the top plates have to be facing up and the bottom dimples must be facing down. Use (1) GriplateTM per mounting point (Figure 7).
Step 6
The GriplatesTM have M4, M5, M6 and M8 hole patterns to fit the hardware that your flat panel requires. Use the M8 mounting points (Figure 6).
DIMPLES
Phillips screw driver
DIMPLES FACING UP
DIMPLES FACING UP
DIMPLES FACING DOWN
M4
M5
M6
M8
DIMPLES FACING DOWN
Bottom of flat panel
Figure 6
Figure 7
-7-
5. 0
WOODEN STUD LOCATION
Step 9
Align the center viewing port from the carton template to the center of the wood studs horizontally. Match the center of viewing port to the center of viewing height desired and mark a line on the bottom of the carton template (Figure 9). NOTE: This marking will reference the center of your flat panel display once mounted on the wall (Figure 9).
Step 8
Using a (commercially available) wood stud finder, locate the 16" or 24" stud centers behind the wall. Once found, make a pencil marking on the center of the wood studs (Figure 8). NOTE: The wall plates have three 16" and one 24" mounting slot positions.
Wood stud finder (commercially available)
Mark the wall and the center of the wood studs.
Center of viewing port
16"
16"
16"
Mark the bottom of the carton template
CENTER OF VIEWING HEIGHT DESIRED
Carton template
Wood studs behind the wall structure
Center of viewing mark
Figure 8
Figure 9
-8-
6. 0
MOUNTING POINT LOCATION
Step 11
Wood Studs: Drill four (4) ¼" pilot holes to the marked wall. Concrete Wall: Drill four (4) 3/8" pilot holes to the marked wall. [. . . ] FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL
Step 15
WARNING:
Raise the flat panel with the mounting brackets secured to the flat panel and insert the top and bottom hooks from each bracket to the rods from the wall plates (Figure 15).
Wall plate
TOP
BOTTOM
Figure 15
9. 0
LATERAL SHIFT ADJUSTMENT
Step 16
Make any lateral shift adjustment and lock it by tightening the two (2) M6 x 30 (mm) Phillips screws found on the bottom of the mounting brackets. CAUTION: Do not over tighten the M6 screws to the rods (Figure 16).
Lateral shift
Figure 16 - 11 -
10. 0 TECHNICAL SPECIFICATIONS
Dimensions are in Inches and (mm)
28. 000 (171. 2) 16. 000 (406. 4)
CL
1. 245 (31. 75)
A B
H
5. 000 (127)
19. 000 (482. 6)
12. 000 (304. 8)
CL
10. 500 (266. 7)
21. 000 (533. 4)
5. 000 (127)
C G
16. 000 (406. 4) 16. 000 (406. 4)
D
F
16. 000 (406. 4)
24. 290 (616. 97)
E
2. 331 (59. 21)
G
A. Safety knobs
H
1
20. 500 (520. 7)
2
FINE TUNE TILT ADJUSTMENTS 1. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MARANTZ WB4001T
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MARANTZ WB4001T will begin.