User manual MAXDATA P2200R CASE

[. . . ] MAXDATA PLATINUM Server Case Users' Manual 2 Contents 1 Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 What Your Kit Includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Feature Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Ensure that the Mylar insulator sheet is seated securely over the standoffs, is laying flat on the chassis floor, and that the edge of the sheet is seated below the studs in the rear chassis wall. While placing the board on the chassis standoffs, carefully position the board I/O connectors in the rear chassis I/O openings. Adjust board position so that the two mounting holes near the board edges rest securely on the two corresponding shouldered standoffs. NOTE The three holes on the server board used to mount the board to the standoffs have white circles around them. Attach the board to the chassis using the three thumbscrews shipped in the chassis accessory kit. Figure 10. Mounting the Server Board 22 Assembling the System Routing Cables Figure 11. Route the backplane power cable (A) from the power supply to the backplane board and connect it to the white 6-pin connector. Route the server board power cable (B) from the power supply to the cable clip and connect it to the white 24-pin connector on the server board. If you are not installing a tape drive, coil the tape drive power cable, wire tie the coil, and place it on the floor. Route the auxiliary signal cable (I) from the power supply to the server board and connect it to 5-pin auxiliary signal connector. Connect the end of the flex circuit cable (C) labeled to the floppy/front panel/IDE connector on the server board. Route the cable to the backplane board and connect the opposite cable end to the matching connector on the backplane. CAUTION After connection of cable (C) in step 5, ensure that each cable connector is properly seated in the board connector. The connector should be parallel to its board connector and not cocked to one side. If in doubt, remove, reinsert, and recheck. MAXDATA PLATINUM Server Manual 23 Figure 12. Locate the end of the SCSI ribbon cable (I) that is labeled baseboard. Route the cable to the backplane board and connect it to the matching connector on the backplane board. Route the backplane power cable (A) from the power supply to the backplane board and connect it to the white 6-pin connector. 8. Insert the cable in the cable clip (**), route it to the backplane, and connect it to the matching connector. Route the cable along the chassis floor at the bottom of the chassis sidewall (*). If you have installed a tape drive, connect the tape drive power cable (D) to the drive. Installing the Fan Assembly CAUTION When installing the fan assembly, avoid pinching cables routed in the area. Ensure the USB cable is routed in the corner where the chassis floor meets the sidewall. Position the fan assembly as shown in Figure 13 and lower it to the chassis floor. While pressing down on the fan assembly, slide it (A) toward the chassis sidewall. [. . . ] The product has been marked with the CE Mark to illustrate its compliance. 44 Regulatory and Certification Information B Safety Warnings WARNING: English (US) MAXDATA PLATINUM Server Manual 45 WARNING: English (US) The power supply in this product contains no user-serviceable parts. Refer servicing only to qualified personnel. Do not attempt to modify or use the supplied AC power cord if it is not the exact type required. A product with more than one power supply will have a separate AC power cord for each supply. The power button on the system does not turn off system AC power. To remove AC power from the system, you must unplug each AC power cord from the wall outlet or power supply. The power cord(s) is considered the disconnect device to the mains (AC) power. [. . . ]