User manual MIDLAND ACC-905CD SOFTWARE GUIDE
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MIDLAND ACC-905CD. We hope that this MIDLAND ACC-905CD user guide will be useful to you.
Manual abstract: user guide MIDLAND ACC-905CDSOFTWARE GUIDE
Detailed instructions for use are in the User's Guide.
[. . . ] 25-pin to 9-pin RS-232 Serial Communications Cable Once located, insert the ACC-2004 Programming Cable into the appropriate serial port on the computer. It is now safe to turn on your computer.
Page -2October 2001
ACC-905 PC PROGRAMMER
For PL2215P, PL2245P, PL2415, PL2445
Connecting the Legacy Radio
ACC-2004 Programming Cable
HARDWARE INSTALLATION
Close Up of Programming Port Legacy Radio
RS-232 Serial Communications Port
IBM Compatible Computer
©
Figure 2. ACC-2004 Installation Once the ACC-2004 programming cable is connected to the computer, the radio can now be connected to the programming cable.
Page -3October 2001
ACC-905 PC PROGRAMMER
For PL2215P, PL2245P, PL2415, PL2445
SOFTWARE INSTALLATION
Making A Backup Copy
(Floppy disk versrion only)
Before installing the ACC-905 Programming Software on your computer, make a backup copy of the disk. The software occupies approximately 5 MB on the disk and can be copied onto four 1. 44 MB disks. [. . . ] Follow the instructions on the program screen as shown below.
GETTING STARTED
Figure 5: Program Screen 4. Once the radio is in Read or write mode, click on the read or write buttons.
Printing a Personality
A personality can be printed by either selecting File and then selecting Print (Alt-F-P) on the menu bar. In order to initiate a call, the user must turn the scan function off by turning the channel selector.
SYSTEM OPTIONS
Priority Scan Channel
This is the channel that will be given priority.
Lookback Time
How often the priority channel is looked at. Range is . 5 to 10 seconds.
Time Out Timer
This is a timer that will limit the time that a user can transmit at any one time.
Time Out Timer Enable
This enables the Time Out Timer.
TX Time Out Time
The amount of time that the radio will enable the user to transmit before timing out and turning off the transmitter. Range is 10 to 2000 seconds.
Time Out Timer Penalty Enable
Once the radio has timed out, this makes the radio wait for a set time before being able to transmit again. Range is 1 to 100 seconds.
Page -10October 2001
ACC-905 PC PROGRAMMER
For PL2215P, PL2245P, PL2415, PL2445
Power Save
This is a battery save feature that makes batteries last longer on a single charge.
Power Save Enable
Enables the Power Save Feature.
Save On Time
This is the amount of time that the receiver is on and looking for calls. Range is 50 to 2000ms.
Save Off Time
This is the amount of time that the receiver is off and not looking for a call. Range is 50 to 2000ms.
Save Delay Time
This is the amount of time that the radio will wait after a call has been received before going back into power save mode. Range is . 5 to 10 seconds.
SYSTEM OPTIONS
Page -11October 2001
ACC-905 PC PROGRAMMER
For PL2215P, PL2245P, PL2415, PL2445
CHANNEL DATA
CHANNEL DATA
Figure 7: Channel Data Tab
RX
Frequency
The frequency that the radio will receive on. This value is set in MHz.
Tone Option
Allows a CTCSS, DCS or Inverted DCS to be applied to any channel. This enables the user to only hear traffic that pertains to them.
IND
Individual Two Tone option. Allows a two tone option to be used as setup in the two tone tab. See "TWO TONE" on page 14.
S-G
Super Group Two Tone option. Allows the super group call to be received as setup in the two tone tab. See "TWO TONE" on page 14.
Page -12October 2001
ACC-905 PC PROGRAMMER
For PL2215P, PL2245P, PL2415, PL2445
TX
Frequency
The frequency that the radio will transmit on. This value is set in MHz.
Tone Option
Allows a CTCSS, DCS or Inverted DCS to be used during transmit. See "TONE OPTIONS" on page 17.
Option
P-SC
Priority Scan Option. This works in conjunction with the Priority Scan Channel feature in the System Option tab. In order for priority scan to work, this field should be set too On for the channels that will lookback to the priority channel.
SC
CHANNEL DATA
Channel Scan. Setting this option to On will put the selected channel in the scan list.
B
Band Option. Setting this option to N will make the selected channel to 12. 5KHz channel spacing. When this is set to S, the channels spacing will be 25KHz.
Page -13October 2001
ACC-905 PC PROGRAMMER
For PL2215P, PL2245P, PL2415, PL2445
TWO TONE
This tab is for setting up the two tone options for the radio.
TWO TONE
Figure 8: Two Tone Tab
Individual Tone 1
This is the first two tone sequence. · Note: When using two tone on a channel, the Tone Option should be set to `No Option'. [. . . ] Range is 100 to 10000Hz.
Gap Time
Time between tone 1 and tone 2 in milliseconds. Range is 100 to 10000Hz.
Tone 2 Disable
Disables tone 2.
Tone 2 Frequency
This is the actual frequency of the second tone in hertz. Range is 300 to 3000Hz.
Tone 2 Duration
How long tone 2 will be sent in milliseconds. Range is 100 to 10000Hz.
TWO TONE
Page -16October 2001
ACC-905 PC PROGRAMMER
For PL2215P, PL2245P, PL2415, PL2445
TONE OPTIONS
Tone Options can be set for Transmit and Receive on the Channel Data Screen. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MIDLAND ACC-905CD
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MIDLAND ACC-905CD will begin.