User manual NAD C720BEE

[. . . ] ® Stereo Receiver SVENSKA Owner's Manual Manuel d'Installation Bedienungsanleitung Gebruikershandleiding Manual del Usuario Manuale delle Istruzioni Manual do Proprietário Bruksanvisning PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH C720BEE IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS · Save these instructions for later use. · Follow all warnings and instructions marked on the audio equipment. 1 Read instructions - All the safety and operating instructions should be read before the product is operated. 2 Retain instructions - The safety and operating instructions should be retained for future reference. [. . . ] Some buttons on this handset are inoperative, as the functions aren't supported by the C720BEE. 2 Power/Standby/Protection LED - Upon switching the power on, the LED will light up red for a few seconds before the protection circuit is deactivated. In cases of serious abuse of the amplifier, such as overheating, excessively low loudspeaker impedance, short circuit etc. the amplifier will engage its Protection circuitry, indicated by the LED turning from green to red, and the sound being muted. In such a case, turn the amplifier off, wait for it to cool down and/or check the speaker connections, making sure the overall loudspeaker impedance doesn't go below 4 ohms. Once the cause for the protection circuitry to engage has been removed, press Power again to resume normal operation. 3 BLEND The Blend button toggles between engaging or disengaging the Blend feature; when engaged, "BLEND" lights up in the VFD. 4 DISPLAY When the AM/FM tuner is the selected input, sequentially pressing DISPLAY shows the currently tuned station's RDS data, toggling between the current station's Radio Text and Station Name displays 5 MEMORY Use to store tuned stations to the C720BEE's 40 presetmemory locations. ITALIANO PORTUGUÊS SVENSKA 6 FM MUTE/MODE - In the normal Mute position, only the stations with a strong signal can be listened to, and the noise between stations is muted. Pressing the [FM Mute/Mode] button allows distant (and potentially noisy) stations to be received. 7 PRESET - Press either PRESET buttons to step up or down between radio presets; 30 FM and 10 AM station presets are available. NOTE that this function "wraps": Pressing the PRESET buttons will step from Preset 30 to Preset 1, or vice versa. (NOTE that Presets must previously have been stored) 8 TUNE - Press either TUNE button momentarily to step up or down between FM or AM frequencies. Press and hold TUNE buttons for more than 2 seconds to search up or down; the C720BEE's tuner will stop at the next sufficiently strong signal it encounters. NOTE that this function, too, "wraps, " and will continue searching up or down from one end of the AM or FM band to the other. NOTE that: TUNE button increments the FM band by 0. 05 MHz steps (twice the precision of most tuners). To change the step amount, select AM and then hold in the FM MUTE/MODE and AM keys simultaneously. 9 Infra-red remote control command receiver - The infrared sensor, located beside the VFD, receives commands from the remote control. There must be a clear line-of-sight path from the remote control to this window; if that path is obstructed, the remote control may not work. NOTE: Direct sunlight or very bright ambient lighting may affect the operating range and angle for the remote control handset. 10 DISPLAY PANEL - The Display Panel shows information about the C720BEE's operating modes and information about the station currently selected, Audio Mute, Blend, FM Mute, Stereo, Centre Tune, etc. The display also has an eight character alphanumeric section, which will display the active input, station name, Radio Text or frequency. [. . . ] Switching the tuner to mono will reduce the amount of noise and hiss but at the expense of any stereo information. The NAD Blend feature will allow you to reduce the amount noise and hiss but still retain some level of stereo separation, instead of mono. The Blend button toggles between engaging or disengaging the Blend feature; when engaged, "BLEND" lights up in the VFD. NOTE: The one can store the same channel in two preset locations; one with FM Blend On, and with FM Blend Off. [. . . ]