User manual NAIM CD5 ISSUE 2

[. . . ] WORLD CLASS HI FI OWNERS MANUAL CD Players: CDS3, CDX2, CD5 ISSUE 2 Introduction Naim Audio products are always conceived with performance as the top priority and careful installation will help ensure that their full potential is achieved. This manual begins with statutory safety warnings and general installation tips for all Naim Audio products. Product specific information begins in Section 6. 2 CONTENTS Page Section 1 1 1 1 Equipment Installation 2 Cables and Connections 3 Getting Started 3. 1 switching on and off 3. 2 running in 3. 3 mains supply 3. 4 siting the equipment 3. 5 if you have a problem 4 Warnings 5 Connection 5. 1 mains lead 5. 2 mains plugs 5. 3 fuse carrier 5. 4 plug fuses 6 CDS3 Installation and Operation 7 CDS3 Rear Panel and Connection Diagrams 8 CDS3 Operation Diagrams 9 CDX2 Installation and Operation 1 Equipment Installation Normally your Naim equipment will have been installed by the dealer who sold it to you even if you live outside their immediate vicinity. Your dealer is responsible for making sure that the system sounds exactly as it should and information given here is not intended to reduce this responsibility in any way. 2 3 4 2 Cables and Connections Please do not modify the standard interconnect cables supplied with your Naim equipment. [. . . ] The full stop on the right of the display window illuminates when the player receives a signal from the remote handset. If a track play list is programmed the time displayed reflects the duration of the program. HDCD: pause: Illuminates to show that an HDCD encoded disc is playing. Flashes to show that pause has been selected from the remote handset. 9. 2 player controls previous: With a disc loaded but not playing the previous button searches the disc contents backwards, either one track at a time, or sequentially if the button is held. While a disc is in play, the previous button searches the table of contents backwards. next: The next button operates in the same way as the previous button, but moving forwards through the disc instead of backwards. Pressing and holding stop will clear any programmed play order, or, if no play order is programmed, will return the player display to its default state (track indication). Play operated while a track is playing will re-start the track. stop: play: Note: If the CDX2 is paused for more than 10 minutes it will enter a "static pause" mode in which the transport laser deactivates and the disc stops spinning - so reducing wear on the transport. The pause indicator will illuminate fully rather than flash when the player is in static pause mode. time: repeat: prog: Illuminates to indicate display of total disc time or elapsed time of the track being played. Illuminates to show that repeat has been selected from the remote handset. Further information on play list programming can be found in Sections 15 and 16. All CD control functions are duplicated on the NARCOM 3 and Flash remote handsets. See Sections 15 and 16 for more information. ®, HDCD®, High Definition Compatible Digital® and Pacific MicrosonicsTM are either registered trademarks or trademarks of Pacific Microsonics, Inc. in the United States and/or other countries. 9 CDX2 9. 5 output Socket Selection A pair of phono output sockets are fitted at the rear of the CDX2 to provide an alternative to the preferred DIN socket. With the player stopped, press and hold the remote handset disp function (handset in CD mode) until the CD player prog text indicator flashes. Further operations of the disp function will now cycle through each combination of the two socket types (DIN only, phono only or both). The selected option is indicated on the CD player display as shown below. Socket Option DIN Phono Both Player Display 9. 7 player maintenance It is important for reliable operation of the CDX2 to ensure that the surfaces of the transport platter and the underside of the puck are free of dust or debris which can prevent the disc from sitting properly and cause it to slip. To clean the transport platter, take a piece of Blu-tack and lightly apply it to the top surface of the magnetic metal hub, picking up any material attached to it. Brush the plastic outer edge lightly with your finger or a soft brush to ensure that it is dust and particle free. Similarly, clean the puck with Blu-tack, to remove debris from the three locating pins on its underside. Do not, under any circumstances, use any solvents or fluids for the cleaning process. O o0 O o0 Press and hold the disp function a second time to exit from socket selection mode. 9. 6 power supply upgrade The CDX2 can be upgraded by the addition of an XPS Power Supply. [. . . ] record: Switches the action of the Soft Keys to select record inputs on appropriately equipped preamplifiers. Compact Disc prev next stop play << & >> repeat pause Selects the previous track or index point. Pauses the cd. Global keys (Preamplifier) Global keys (CD Player) Global keys (Tuner) Tuner mode Switches the tuner sequentially through manual, scan and preset modes. Modes are indicated by the scan and preset indicators on the tuner display. Soft keys up & down These keys both have three possible functions depending upon the selection of the mode key. In manual mode the up and down keys adjust the tuning frequency in 0. 1MHz steps. [. . . ]