User manual NOVAK 828-HV
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NOVAK 828-HV. We hope that this NOVAK 828-HV user guide will be useful to you.
Manual abstract: user guide NOVAK 828-HV
Detailed instructions for use are in the User's Guide.
[. . . ] Minimum Drive (1 or 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-15% 4. Timing Level (1 of 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timing Set Point (1 of 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Current Limit (1 of 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use caution when operating vehicle and do not operate around other people or in an unsafe manner to avoid injuries or damage.
Speed Control Runs Excessively Hot
· Improper gearingRefer to `PROPER GEAR SELECTION' section. · Motor rotation is set to clockwiseElectronic motor timing advancement only functions in counter-clockwise rotation direction (refer to `CUSTOM PROGRAMMING OPTIONS'). · Timing Set Point set incorrectlyRefer to `CUSTOM PROGRAMMING OPTIONS' section.
· Electronic motor timing set too highreduce timing level setting in ESC. · Gear ratio too lowIncrease gear ratio/Reduce pinion (refer to `PROPER GEAR SELECTION'). TURN ON THE SPEED CONTROL'S POWER
Model Runs Slowly/Slow Acceleration
· · · ·
With transmitter throttle at neutral, and still pressing the SET button, slide the ESC's ON/OFF switch to ON position.
ESC Is Melted Or Burnt/ESC Runs With Switch Off
· Internal damageRefer to Service Procedures.
Gear ratio too highReduce gear ratio/Increase pinion (refer to `PROPER GEAR SELECTION'). Check battery & connectorsCheck battery pack & connectors. Incorrect transmitter/ESC adjustmentRefer to `TRANSMITTER ADJUSTMENTS'. Power Trans-Cap Module damaged/missingReplace Power Trans-Cap Module.
4. PULL TRANSMITTER THROTTLE TO FULL-ON POSITION
Hold it there until the green status LED turns solid green. Hold it there until the green status LED blinks green.
No Power to the BEC
7. RETURN TRANSMITTER THROTTLE TO NEUTRAL
The red status LED will turn solid red, indicating that speed control is at neutral and that proper programming has been completed. GREEN flashing LED = hotter operating temp--168-194°F (76-90°C). RED flashing LED = hottest operating temp--195-215°F (91-102°C). You are now pushing the ESC extremely hard and should be very careful to avoid overheating and possible thermal shut-down. All LEDs flashing = DANGEROUS operating temp--216-239°F (103-115°C). Your ESC is now about to thermally shut-down.
THROTTLE CHANNEL ADJUSTMENTS A. Set ELECTRONIC TRIGGER THROW ADJUSTMENT to 50% throttle and
[adjusts neutral position/increases or decreases coast brakes] 50% brake throwbest for reversible ESCs. [adjusts trigger throw electronic/digital pistol-grip transmitters] G. While this feature can not guarantee the survival of the speed control when subjected to conditions that produce excessive heating of the electronics, it does provide another tool that you can use to avoid extensive damage.
---Reduce the pinion size to avoid overheating and potential ESC damage---
www. teamnovak. com
Best to use
OK to use
Do not use
If you notice a significant decrease in performance of your brushless system during a run, immediately check the operating temperatures of the speed control and the motor. Reduce gearing or ESC timing settings to lower operating temperatures!
P5
P8
CUSTOM programmiNG options -- advanced
kinetic 1S software flow chart
The Kinetic 1S ESC features over a dozen parameters that can be customized to fine-tune the ESC's feel & response to your liking. The flow chart below and the adjustment steps to the right describe the different parameters and how they effect the ESC. One-Touch Programming must be completed before customization of parameters, as all ESC parameters are defaulted back to the factory settings whenever the One-Touch Programming is performed.
DEFAULT SETTINGS FOR THE ESC PARAMETERS ARE LISTED IN BOLD IN THE TABLES TO THE RIGHT
@NEUTRAL
RED LED on solid press & hold SET button
minimum brake
#1 MINIMUM BRAKE SETTINGS (1 of 10) BLUE LED
Amount of braking applied with the first pulse of transmitter throttle information sent. [. . . ] Minimizes trigger throw required before effective drive is applied with heavy vehicles.
BRAKE CURVE
#9 BRAKE CURVE SELECTION (1 of 2) RED & WHITE LEDs
How the ESC's brakes respond to the transmitter's trigger input. >> Changing this setting changes how the brakes respond to your transmitter's trigger movement. The `Expo' curve gives a less responsive, or more forgiving low-end braking.
voltage cut-off
#15 VOLTAGE CUT-OFF SELECTION (1 of 3) YELLOW & RED LEDs
>> Changing this setting enables or disables the ESC's Smart Stop cut-off circuitry, and also sets the voltage cut-off point based on what type of batteries are being used in the vehicle's main battery pack. DO NOT USE LiPo/LiFe BATTERIES WITH VOLTAGE CUT-OFF TURNED OFF
THROTTLE CURVE
GREEN & WHITE
BRAKE CURVE
RED & WHITE
Setting (# of flashes)
Minimum Drive (%):
1 0
2 1
3 2
4 3
5 4
6 6
7 8
8
9
10
10 12 15
Setting (# of flashes)
Brake Curve:
1 Linear
2 Expo
BRAKE FREQ.
RED
TIMING level
#4 TIMING LEVEL SETTINGS (1 of 8) GREEN-RED-WHITE LEDs
The maximum degrees of Dynamic Timing Advance applied to the motor. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE NOVAK 828-HV
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NOVAK 828-HV will begin.