Detailed instructions for use are in the User's Guide.
[. . . ] MOUNT SMART BOOST
Find a suitable installation point in the vehicle, preferably close to the ESC and receiver so the included receiver harness will easily reach it.
OPERATION
1. SMART BOOST SETUP
No setup is necessary for the module.
INSTALLATION (refer to Fig. MOUNT SMART BOOST
Find a suitable installation point in the vehicle, preferably close to the ESC and receiver so the included receiver harness will easily reach it.
OPERATION
1. [. . . ] It is important to leave the ESC's original switch in the OFF position while running the system.
NOTE: With some Novak ESCs that include built-in servo voltage protection, it may be necessary to switch ON, then after a moment, switch OFF the ESC's switch for proper operation.
2. POWER UP SMART BOOST
To turn the vehicle's power on, simply turn the Smart Boost's switch ON. It is important to leave the ESC's original switch in the OFF position while running the system.
NOTE: With some Novak ESCs that include built-in servo voltage protection, it may be necessary to switch ON, then after a moment, switch OFF the ESC's switch for proper operation.
A. If mounting in a nitro vehicle, install the Smart Boost near the receiver battery pack to ensure the input harness will reach the vehicle's receiver. If mounting in a nitro vehicle, install the Smart Boost near the receiver battery pack to ensure the input harness will reach the vehicle's receiver. PREPARE WIRES FOR INSTALLATION
The Smart Boost's red and black 20G-silicone power wires connect to the ESC's battery power wires (where the ESC's main-battery wires connect to the ESC's PCB). Cut the wires to proper length and strip 3/16"1/4" of insulation off the ends and tin with solder.
2. POWER DOWN SMART BOOST
When finished running the vehicle, simply turn OFF the Smart Boost's switch.
The Smart Boost's red and black 20G-silicone power wires connect to the ESC's battery power wires (where the ESC's main-battery wires connect to the ESC's PCB). Cut the wires to proper length and strip 3/16"1/4" of insulation off the ends and tin with solder.
3. Fill out the needed information on this form and return it with the Novak product that requires servicing.
PRODUCT WARRANTY
The Smart Boost Module is guaranteed to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (verified by dated, itemized sales receipt). Warranty does not cover incorrect installation, components worn by use, damage from using more than 1 LiPo cell input voltages, tampering with internal electronics, allowing water, moisture or any other foreign material to enter module or get onto the PC board, or any damage caused by a crash, flooding or natural disaster. Because Novak has no control over the connection & use of the module, no liability may be assumed nor will be accepted for any damage resulting from the use of this product. Every Novak module is thoroughly tested before leaving our facility and is, therefore, considered operational. By the act of connecting/operating module, user accepts all resulting liability. In no case shall our liability exceed the product's original cost. · All Rights Reserved · No part of these instructions may be reproduced without the written permission of Novak Electronics, Inc. · Smart Boost 1-Cell Li-Po Step-Up Module is a trademark of Novak Electronics, Inc.
SERVICE PROCEDURES
After reviewing instructions, if you feel that your module requires service, please obtain the most current product service options and pricing by the following ways: WEB SITE: Print a copy of the PRODUCT SERVICE FORM from the CUSTOMER SERVICE section of the Web site. Fill out the needed information on this form and return it with the Novak product that requires servicing.
PRODUCT WARRANTY
The Smart Boost Module is guaranteed to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (verified by dated, itemized sales receipt). [. . . ] Warranty does not cover incorrect installation, components worn by use, damage from using more than 1 LiPo cell input voltages, tampering with internal electronics, allowing water, moisture or any other foreign material to enter module or get onto the PC board, or any damage caused by a crash, flooding or natural disaster. Because Novak has no control over the connection & use of the module, no liability may be assumed nor will be accepted for any damage resulting from the use of this product. Every Novak module is thoroughly tested before leaving our facility and is, therefore, considered operational. [. . . ]