User manual NOVAK ELEKTRA
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NOVAK ELEKTRA. We hope that this NOVAK ELEKTRA user guide will be useful to you.
Manual abstract: user guide NOVAK ELEKTRA
Detailed instructions for use are in the User's Guide.
[. . . ] Never allow water, moisture, or other foreign materials to get inside the ESC. · 6 CELLS ONLY Never use more or fewer than 6 sub-C cells (1. 2 volt DC/cell) in the main battery pack. · MOTOR CAPACITORS REQUIRED Three 0. 1µF (50V) ceramic capacitors must be properly installed on every motor to prevent radio interference. · DO NOT REMOVE BATTERY OR MOTOR CONNECTORS Internal damage can occur and will void the warranty. [. . . ] INSTALL THE ANTENNA Mount the antenna as close to the receiver as possible. Do not cut or coil excess wire.
Cutting or coiling excess wire will reduce radio range.
INSTALLATION EXAMPLES
All Novak ESCs are guaranteed to be free from defects in materials and workmanship for a period of 120 days from the original date of purchase. Complete warranty details inside.
Input Voltage Case Width Case Depth Case Height Weight (w/o heat sinks) On-Resistance @ Transistors Rated Current Braking Current BEC Rating Motor Limit Wire Size (Battery/Motor) Wire Length (Battery/Motor) Signal Harness Length PWM Drive Frequency
6 cells (1. 2 volts DC/cell) 1. 75 inches [44. 45 mm] 1. 36 inches [34. 59 mm] 0. 73 inch [18. 42 mm] 1. 71 ounces [48. 48 g] 0. 010 (25°C junction temp. ) 120 amps 40 amps 5. 0 volts DC / 0. 5 amps 20 turns 16 gauge 6 inches [152 mm] 6 inches [152 mm] 500 hertz (nominal)
PART #1930
OPERATING INSTRUCTIONS
#1930
STEP 3
HOOK-UP INSTRUCTIONS
Refer to set-up photo below
STEP 4
TRANSMITTER ADJUSTMENT
Proper transmitter adjustment is important for optimum performance from your speed control. The basic throttle channel adjustments for the transmitter are as follows: 1. Set HIGH ATV or EPA to maximum setting.
[Controls amount of throw from neutral to full throttle]
TROUBLE-SHOOTING GUIDE
This section describes possible speed control problems, causes, and solutions.
1. INSTALL MOTOR CAPACITORS Electric motors generate radio noise that can interfere with your receiver and cause radio problems. Included in the accessory kit with the speed control are three 0. 1µF (50V) non-polarized, ceramic capacitors. These capacitors must be installed on every motor to help reduce the noise generated by the motor and also to prevent possible damage to the speed control. Solder 0. 1µF (50V) capacitors between: · POSITIVE (+) motor tab & NEGATIVE (-) motor tab. *If your motor does not have a ground tab, solder the capacitor leads to the can of the motor as shown below.
Negative (-) motor tab 0. 1µF Capacitors Schottky diode Positive (+) motor tab
Steering Channel Works But Motor Will Not Run
· Speed control has thermally shut downAllow ESC to cool downUse milder motor or smaller pinion gear. · Make sure ESC is plugged into the throttle channel of receiver. · Possible internal damageRefer to Service Procedures.
2. Set LOW ATV, EPA, or ATL to maximum setting.
[Controls amount of throw from neutral to full brakes] [Reduce this after ESC adjustment to reduce amount of brakes]
3. Set EXPONENTIAL to zero setting.
[Controls the linearity of the throttle channel]
Receiver Glitches/Throttle Stutters During Acceleration
· Motor capacitors broken or missingRefer to Step 3. · Receiver or antenna too close to speed control, power wires, battery, or motorRefer to Step 2. · Excessive current to motorUse a milder motor or a smaller pinion gear.
4. Set THROTTLE CHANNEL TRIM to middle setting.
[Adjusts the neutral position of speed control] [Increase or decrease after ESC adjustment to adjust coast brakescan be used to give braking in neutral trigger position]
5. Set THROTTLE CHANNEL REVERSING SWITCH to either position.
[Do not change switch position after programming]
Motor and Steering Servo Do Not Work
· Check wires, receiver signal harness wiring and color sequence, radio system, crystals, battery and motor connectors, and battery pack. · Possible internal damageRefer to Service Procedures.
6. Set ELECTRONIC TRIGGER THROW ADJUSTMENT to 70% throttle and 30% brake throw (or 7:3).
[Adjusts pistol-grip transmitter's throttle trigger throw]
Model Runs Slowly / Slow Acceleration
· Check motor and battery connectorsReplace if needed. · Incorrect transmitter or speed control adjustmentRefer to Steps 4 and 5. · Optional external Schottky diode (if used) installed backwards or damagedRefer to Step 3.
Extra 0. 1µF capacitors available in Novak kit #5620.
Ground / motor can
7. [. . . ] guarantees the Elektra to be free from defects in materials and workmanship for a period of 120 days from original date of purchase (verified by dated, itemized sales receipt). Warranty does not cover incorrect installation, components worn by use, damage from using fewer or more than 6 cells (1. 2 volts DC/cell) input voltage, not using heat sinks, shortcircuiting heat sinks, cross-connection of battery/motor or reverse voltage application, damage from incorrect installation of FET servo or receiver battery pack, damage from excessive force while installing heat sinks or pushing One-Touch button, not installing three 0. 1µF (50V) capacitors on motor, splices to switch or receiver signal harnesses, removing or changing the battery or motor connectors, damage from disassembling case, tampering with internal electronics, allowing water, moisture, or any other foreign material to enter ESC or get onto PC board, allowing exposed wiring to short-circuit, or any damage caused by a crash. has no control over connection and use of the ESC, no liability may be assumed nor will be accepted for damage resulting from the use of this product. Every ESC is thoroughly tested and cycled before leaving our facility and is, therefore, considered operational. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE NOVAK ELEKTRA
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NOVAK ELEKTRA will begin.