User manual NOVAK M2 DIG BASIC SET UP GUIDE
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NOVAK M2 DIG. We hope that this NOVAK M2 DIG user guide will be useful to you.
You may also download the following manuals related to this product:
NOVAK M2 DIG V1.0 (612 ko)
NOVAK M2 DIG FIELD GUIDE (386 ko)
Manual abstract: user guide NOVAK M2 DIGBASIC SET UP GUIDE
Detailed instructions for use are in the User's Guide.
[. . . ] STEP 5-one-touch programming
With ESC connected to (at least) a receiver and a charged battery pack, and the transmitter's Aux/3rd channel (3Ch required for Dig) set to its middle position:
OPTIONAL RECEIVER PACK USAGE
If you are planning to use an external receiver battery pack with the M2 Dig 3S ESC to power the electronics you need to do the following: 1. Plug the external 5 cell (1. 2VDC/cell) receiver battery pack into the battery slot of the receiver. Then, turn the ESC's switch ON, then OFF to allow the ESC to be powered by an external source. Plug the external 5 cell (1. 2 VDC/Cell) receiver battery pack into the battery slot of the receiver. [. . . ] Use of this product in an uncontrolled manner may result in physical damage or injuries--take extra care when operating any remote control vehicle. · All Rights Reserved · No part of these instructions may be reproduced without the written permission of Novak Electronics, Inc. The two sets of three pins behind the power output pins are for the input signal harnesses. The polarity is the same for both: Positive in the middle, Negative on the left, and signal on the right.
25x25x10mm COOLING FANS [Novak kits #5647 & #5651] POWER-CAP HARNESS [Novak kit #5682]
Using LiPo batteries that cannot supply the amount of current required by this system will result in possible battery pack, ESC & motor damage, and will void the warranty. It is recommended to use a 25C or higher rating.
GOOD QUALITY LiPo BATTERIES SUGGESTED
Black auxilliary cooling fan fits ESC's heat sink perfectly & has 2-pin plug for easy connection. Required for use.
Always turn on the power of the transmitter first so that you will have control of the vehicle when you turn it on.
TRANSMITTER ON FIRST
POWER TRANS-CAP MODULE3S LiPo [Novak kit #5686]
Optional Power Trans-Cap module. Lowers operating temperatures.
LOW-LOSS POWER CONNECTORS3. 5mm [Novak kit #5731] LEAD-FREE SILVER SOLDER [Novak kit #5831-#5833]
Gold-plated Low-Loss connectors for wiring electronics. Novak solder contains 3% Silver for high-conductivity and is available in three sizes. 6g in Novak kit #5831, 15g in Novak kit #5832, and 100g in Novak kit #5833.
With the higher performance systems, undesirable radio system noise may occur when used with lower quality radio systems (like some RTR radios).
GOOD QUALITY RADIO SYSTEM SUGGESTED
DO NOT BUNDLE POWER & SIGNAL WIRES TOGETHER
RF noise in the power wires can adversely effect radio system performance.
MOUNTING TAPE 25x35mm [Novak kit #5840 & #5841] HEAT SHRINK TUBING [Novak kit #5850 & #5851]
Premium Novak double-sided mounting tape to secure electronics in vehicles. Novak heat shrink tubing is 6" long and available in six sizes: 1/16" - 3/8". 6 piece assortment in Novak kit #5850, and 24 piece assortment in Novak kit #5851.
Always insulate exposed wiring with heat shrink tubing or electrical tape to prevent short circuits. Exposure to CA glue or its fumes can cause damage to internal components of the ESC and result in premature failure.
INSULATE WIRES NO CA GLUE
FIGURE 5
positive negative fan pin fan pin
P4
www. teamnovak. com
P1
step 1connect input harness
DUAL-BRUSHED MOTOR SET-UP PHOTO
The M2 Dig has user-replaceable input harnesses with the industry-standard 3-pin JST connector on both ends, and works with all major radio brand's new receivers (Refer to Figure 1 to see how to connect the included user-replaceable input harness). Black power wire
(battery negative)
PowerCap (Novak #5682) Battery connector
(not included)
Power Trans-Cap Module
(Novak #5686)
or optional
Blue wires to motor negative ()
Note: Most MOA vehicles require that the one of the motor's power wires be reversed for proper rotation.
step 3Wire esc to motors
1. MOTOR CAPACITORS
Electric motors generate RF noise that can cause radio interference. The included 0. 1µF (50V) [Novak #5620] non-polarized, ceramic capacitors may be used to reduce motor noise, if needed. Solder 0. 1µF (50V) capacitors between: · POSITIVE (+) motor tab & NEGATIVE () motor tab. · POSITIVE (+) motor tab & Motor Can · NEGATIVE () motor tab & Motor Can Positive (+) motor tab 0. 1µF Capacitors Grounded motor capacitors Negative (-) motor tab
1. CONNECT ESC TO AUX/CH. 3 OF RECEIVER
The throttle channel harness connects to the 3-pin header closest to the edge of the ESC's case.
Ch. 3 Ch. 2
Red power wire
(battery positive)
(FIGURE 2)
FIGURE 1
Input harnesses plugged into Ch. 2 & Ch. 3 of receiver.
Cooling fan recommended for 3S LiPo use
(refer to Fig. 5)
ESC ON/OFF Switch
FIGURE 4
step 2mount esc
Mount the ESC so the power wires are as far away from other electronics as possible. Make sure that the ESC or the power wires will not interfere with any moving parts in the vehicle. Select a location that has good cooling and allows airflow through heat sinks.
Status LEDs
Power output pins Userreplaceable input signal harness (Ch. 2)
One-Touch button Terra Claw Crawling Brush Motor55T
(Novak #3556)
If the ESC gets air flow, it will run cooler; and that means it will be more efficient!
1. MOUNT SPEED CONTROL IN VEHICLE
Use the included double-sided tape to mount the speed control in vehicle (do not use glue). [. . . ] This is important, as the receiver & servo electronics may be damaged if the sequence is incorrect. For instructions on changing the wiring sequence for older receivers, visit the Novak Web site.
(+)
Wires cut to length
Yellow wires to motor positive (+)
2-3cell LiPo battery pack 2-3cell LiPo battery pack
Motor can
Do NOT to touch capacitor leads to motor can, except for the capacitors that are grounded to the can.
Install pinion on motor and align pinion and spur gears. You NEED a small amount of play between the pinion gear and the spur gear (about the thickness of a piece of paper)check the free play at several positions around the spur gear to ensure a proper mesh (just in case the gears are out of round). Tighten motor mounting screwsAvoid using excessive force that could break
screws or strip the threaded holes in motor. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE NOVAK M2 DIG
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NOVAK M2 DIG will begin.