User manual OPTOMA H31
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual OPTOMA H31. We hope that this OPTOMA H31 user guide will be useful to you.
You may also download the following manuals related to this product:
OPTOMA H31 Product Brochure (569 ko)
Manual abstract: user guide OPTOMA H31
Detailed instructions for use are in the User's Guide.
[. . . ] Table of Contents
English
Usage Notice
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Introduction
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the "Power" button again to confirm, otherwise the message will disappear after five seconds. When the projector is off, the "Power" LED indicator will be orange for approximately 120 seconds while the lamp is cooling. Only after the "Power" indicator blinks green and the projector is in the standby mode, the power cord can be unplugged from the unit. Do not turn on the projector immediately following a power off procedure.
English
When the "LAMP" indicator lights orange continuously, the lamp may failed. When the "TEMP" indicator flashes orange for about ten seconds, you will see a message "Fan Fail" or "Over Temperature"on the display. After cooling, under normal conditions, the projector can be switched on again for your presentation. If the problem persists, contact your local reseller or service center.
12
Installation
English
Adjusting the Projected Image
Adjusting the Image Height
The projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image : 1. While holding down the elevator button, adjust the foot to the desired height, then release the button to lock the elevator foot into position. Lower the projector so it rests on its foot; adjust as needed.
1
Elevator Foot
3
2
Tilt-adjustment Foot
Elevator Foot
13
Installation
Adjusting the Projector's Zoom/Focus
You may adjust the zoom to zoom the lens in or out. To focus on the image, turn the focus ring until you see a clear image. The projector will focus at distances from 4. 6 to 39. 4 feet (1. 4 to 12. 0m).
English
Zoom Ring Focus Ring
14
User Controls
Remote Control & Remote Control
There are two ways to control the functions: with remote control and control panel.
English
Remote Control
Control Panel
Using the Remote Control Power
4 "Power" turns on the projector's lamp. Refer to the "Powering
On/Off the Projector" section on page 11~ 12 for more details.
Hide
4 "Hide" immediately turns the screen black. Press "Hide" again
to restore the displayed image.
Freeze
4 "Freeze" pauses the screen image, press "Freeze" again to unpause.
Re-Sync
4 Automatically synchronizes the projector with the input source.
15
User Controls
Brightness
English
4 Adjust the brightness of the image.
Zoom
4 Zoom in or out.
Contrast
4 Control the degree of difference between the lightest and
darkest parts of the picture.
Keystone +/-
4 Correct image distortion caused by tilting the projector.
4:3
4 Scale the image at a 4:3 aspect ratio.
16 : 9
4 Scale the image at a 16:9 aspect ratio.
Letterbox
4 Enable the viewing of a 2. 35:1 or 1. 85:1 movie without black
Image shift
bars at the left and right of the screen. Some of the original image will be lost from the up and down edges of the screen.
4 Shifts the projected image position vertically.
Four Directional Select Keys
4 Press "Menu, " then use
Enter
to select menu items or to
make adjustments to your selection.
4 Confirm your selection.
Menu
4 Display or exits the onscreen display menu.
DVI-A
4 Choose DVI-Analog source.
DVI-D
4 Choose DVI-Digital source.
Composite S-Video
4 Choose video source. 4 Choose S-Video source.
Component
4 Choose Component-i and Component-p sources. Language Bulb Source Lock Auto Shutdown Blanking Bright Mode High Altitude DISPLAY. . . . . . . . . . . . . . . Projection Format Keystone Zoom Mode Full Screen Mode 4:3 Mode 1080i Mode Lens Shift Preset Edge Mask
Lamp Hour/Lamp Reminding/ Lamp Reset On/Off On/Off Blue/Black On/Off On/Off Front Desktop/Front Ceiling/Rear Desktop/Rear Ceiling 4:3/16:9
Normal/1. 66/1. 85/2. 35 Mode 1/Mode 2/Mode 3 Mode 1/Mode 2 1/2/Off On/Off
19
User Controls
PICTURE
English
Mode Contrast Brightness Color Tint Sharpness Gamma Reset
Cinema 50 50 50 50 50 1
PICTURE
Mode
There are three factory presets optimized for various types of pictures: cinema, normal, and vivid. You can customize contrast, brightness, intensity, color, tint, sharpness, and gamma for each preset mode.
Contrast
Contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.
4 Press to decrease the contrast. Brightness
Adjust the brightness of the image.
4 Press 4 Press Color
to darken image. to lighten image.
Adjust a video image from black and white to fully saturated color.
The "Tint" sub menu is not supported under the Component Video or Analog RGB input sources.
4 Press 4 Press Tint
to decrease the amount of color in the image. to increase the amount of color in the image.
Adjust the color balance of red and green.
4 Press to increase the amount of green in the image. [. . . ] From the "My Computer" icon, open the "Control Panel" folder, and double click the "Display" icon. If the projector is still not displaying the entire image, you may need to change the monitor display that you are using. Verify the resolution setting is less than or equal to 1280 x 1024 resolution. Select the "Change" button under the "Monitor" tab . [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE OPTOMA H31
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual OPTOMA H31 will begin.