User manual ROCKTRON REPLITONEMP

[. . . ] Digital Modeling Preamp MANUAL o o o o o o 16 Amplifier Emulations Direct Recording Capabilities 128 User Programable Presets Available HUSH ® Noise Reduction Rocktron's Hallmark Effects Reverb, Delay, HUSH, & one additional effect available at all times! Suggested Footcontroller(s) - Rocktron MIDI Mate, Rocktron MIDI I. T. ® Suggested MIDI Cable(s) - Rocktron M7 Pin MIDI Cable Model # RMM900 Suggested Power Amplifier(s) - Rocktron Velocity 100 (2x50 Watt) Suggested Speaker Cabinets(s) - Rocktron Velocity S112 (1x12 cabs) ® May be covered by one or more of the following: U. S. Patents #4538297, 4647876, 4696044, 4745309, 4881047, 4893099, 5124657, 5263091, 5268527, 5319713, 5333201, 5402498 and 5493617. Foreign patents pending. 1 Your Rocktron RepliTone MP TM preamp has been tested and complies with the following Standards and Directives as set forth by the European Union: Standard(s): IEC60065 Professional Audio/Video or Similar Equipment, EN55013:1997, EN61000-3-2 (1995) EN61000-3-3(1995), EN55020:1995, CSA E65-94 This means that this product has been designed to meet stringent guidelines on how much RF energy it can emit, and that it should be immune from other sources of interference when properly used. [. . . ] 4 HEADPHONE/DIRECT/RECORDING OUTPUT jack Plugging either headphones or a stereo Y cable into this jack will activate the RepliTone MP's speaker simulator. This jack has been specifically designed to be used in several ways: -For Direct Recording (use a stereo Y cable for left and right) -For Direct connection to a PA system (use a stereo Y cable for left and right) -For Headphone listing. This feature allows you to use a stereo Y cable (not included) to run into a PA system (eliminating the need to haul the power amp and speaker cabinets to the gig) or allow you to record direct into a mixing board or home studio. If you do not have a stereo Y cable you can activate the speaker simulator out of the Left & Right Pre-amp outputs by plugging in a 1/4" guitar cable or 1/4" stereo dummy jack into this headphone/direct/recording output jack and then use two standard 1/4" guitar cables from the Pre-amp outputs into the PA or recording device. 5 LOOP SEND and RETURN jacks The effects loop is provided to allow for a chain of external stereo (L/R) effects devices to be inserted into the signal path after the preamp and built-in effects and before the power amp. NOTE: To maintain stereo operation, the effects loop must be used in a stereo configuration. This requires only stereo RTS connections to be made to the send and return jacks. Using mono TS (tip-sleeve) connections will mute the right channel. 6 POWER jack and ADAPTER Provides AC power to the Replitone MP - please use the enclosed 9VAC 3. 4 amp adapter for this product only. Please follow all precaution instuctions included in the front of this manual. Here are the model numbers: Model Number 006-1211 - this is a 110V 9VAC 3. 4A Adapter 4 Pin/Din for RepliTone MP Model Number 006-1224 - this is a 220V 9VAC 3. 4A adapter 4 Pin/Din for RepliTone MP Please check our website for more details www. rocktron. com 11 11 8. The first 15 are accessible from the front panel PRESET knob and correspond to MIDI program change numbers 1 to 15. ("Manual" is not a MIDI accessible preset. ) The remaining 113 user presets are accessible only via MIDI program changes (program numbers 16 to 128) through a footcontroller. The MIDI IN jack is a 7-pin DIN for phantom powering MIDI controllers, however, 5-pin DIN cables can be used and are most common. The MIDI channel will be permanently set to OMNI, you can plug in any MIDI pedal and it will work. However for the best function we recommend the Rocktron MIDI Mate or MIDI I. T. and the RMM900 7pin MIDI Cable. Storing Presets o Storing Presets to Exisiting Location: Once you have achieved a sound that you like, you may want to save it for later use. If you would like to store the changed sound at the current or exisiting preset - press the store button again to execute the change or complete the store. o Storing Presets to a different location: If you would like to save the changed sound to a different preset - press the STORE (EXECUTE) button. Now turn the preset knob to the number where you want to save or choose the location number on your MIDI Footcontroller. You will now hear the sound of the preset location which you selected when turning the knob. At this point the LED will turn OFF and the sound that you had created will be stored to that preset location. Note: To cancel any store, turn the "AMP" select knob in any direction and the store will be cancelled. Note: The RepliTone MP's unique function requires that the modulation effect be adjusted last before storing a preset. The modulation effects are Chorus, Flanger, Tremolo 1, Tremolo 2, Phaser, Rotary and Detune/Pitch. [. . . ] The Regen and Pan positions allow you to use the EFFECT ADJUST knob to set the Regeneration (the number of times the signal repeats itself) on Delay Regen and the Pan (movement of the signal between the left and right channels) on Delay Pan. Delay Regen & Delay Pan Phaser Phase shifting involves splitting the input signal into two signals, then shifting the phase of different frequencies of one signal and mixing it back with the original signal. This also creates a comb filter like the flanger, but without as many "teeth". Higher parameter settings result in the sweep of the filtering effect occurring over a wider frequency range. Tremolo 1 & 2 Tremolo is the rapid wavering of the volume (not pitch, like vibrato) that makes your guitar sound as if you are playing it through a slowly moving electric fan. Tremolo 1 has a triangle wave modulation which is slightly more subtle than Tremolo 2 which has a square wave modulation for a more pronounced effect. [. . . ]