User manual TEXAS INSTRUMENTS STELLARIS LM3S1110 DATA SHEET REV D

[. . . ] TE X AS INS TRUM E NTS - P RO DUCTI O N D ATA Stellaris® LM3S1110 Microcontroller D ATA SHE E T D S -LM 3S 1110 - 7 3 9 3 C opyri ght © 2007-2010 Texas Instr uments Incor porated Copyright Copyright © 2007-2010 Texas Instruments Incorporated All rights reserved. Stellaris and StellarisWare are registered trademarks of Texas Instruments Incorporated. ARM and Thumb are registered trademarks and Cortex is a trademark of ARM Limited. Products conform to specifications per the terms of Texas Instruments standard warranty. [. . . ] For details about bit-banding, please refer to Chapter 4, "Memory Map" in the ARM® CortexTM-M3 Technical Reference Manual. 8. 2. 2 Flash Memory The flash is organized as a set of 1-KB blocks that can be individually erased. Erasing a block causes the entire contents of the block to be reset to all 1s. An individual 32-bit word can be programmed to change bits that are currently 1 to a 0. These blocks are paired into a set of 2-KB blocks that can be individually protected. The protection allows blocks to be marked as read-only or execute-only, providing different levels of code protection. Read-only blocks cannot be erased or programmed, protecting the contents of those blocks from being modified. Execute-only blocks cannot be erased or programmed, and can only be read by the controller instruction fetch mechanism, protecting the contents of those blocks from being read by either the controller or by a debugger. See also "Serial Flash Loader" on page 392 for a preprogrammed flash-resident utility used to download code to the flash memory of a device without the use of a debug interface. 8. 2. 2. 1 Flash Memory Timing The timing for the flash is automatically handled by the flash controller. However, in order to do so, it must know the clock rate of the system in order to time its internal signals properly. The number of clock cycles per microsecond must be provided to the flash controller for it to accomplish this timing. It is software's responsibility to keep the flash controller updated with this information via the USec Reload (USECRL) register. On reset, the USECRL register is loaded with a value that configures the flash timing so that it works with the maximum clock rate of the part. If software changes the system operating frequency, the new operating frequency minus 1 (in MHz) must be loaded into USECRL before any flash modifications are attempted. For example, if the device is operating at a speed of 20 MHz, a value of 0x13 (20-1) must be written to the USECRL register. 8. 2. 2. 2 Flash Memory Protection The user is provided two forms of flash protection per 2-KB flash blocks in one pair of 32-bit wide registers. The protection policy for each form is controlled by individual bits (per policy per block) in the FMPPEn and FMPREn registers. Flash Memory Protection Program Enable (FMPPEn): If set, the block may be programmed (written) or erased. Flash Memory Protection Read Enable (FMPREn): If a bit is set, the corresponding block may be executed or read by software or debuggers. If a bit is cleared, the corresponding block may only be executed, and contents of the memory block are prohibited from being read as data. Flash Protection Policy Combinations FMPPEn 0 1 FMPREn 0 0 Protection Execute-only protection. This combination is unlikely to be used. 138 Texas Instruments-Production Data June 23, 2010 Stellaris® LM3S1110 Microcontroller Table 8-1. Flash Protection Policy Combinations (continued) FMPPEn 0 FMPREn 1 Protection Read-only protection. This mode is used to lock the block from further modification while allowing any read or execute access. [. . . ] 108-Ball BGA Package June 23, 2010 Texas Instruments-Production Data 413 Package Information Note: The following notes apply to the package drawing. Symbols A A1 A3 c D D1 E E1 b bbb ddd e f M n MIN 1. 22 0. 29 0. 65 0. 28 9. 85 NOM 1. 36 0. 34 0. 70 0. 32 10. 00 8. 80 BSC MAX 1. 50 0. 39 0. 75 0. 36 10. 15 9. 85 10. 00 8. 80 BSC 10. 15 0. 43 0. 48 . 20 . 12 0. 80 BSC 0. 53 - 0. 60 12 108 REF: JEDEC MO-219F - 414 Texas Instruments-Production Data June 23, 2010 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. [. . . ]