User manual TOYOTA SPA15
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual TOYOTA SPA15. We hope that this TOYOTA SPA15 user guide will be useful to you.
You may also download the following manuals related to this product:
TOYOTA SPA15 (1101 ko)
TOYOTA SPA15 (1102 ko)
TOYOTA SPA15 (1096 ko)
Manual abstract: user guide TOYOTA SPA15
Detailed instructions for use are in the User's Guide.
[. . . ] SP10 Series
HOME-USE SEWING MACHINE
INSTRUCTION MANUAL
· Read this manual carefully before use and always follow the
instructions.
· Keep the manual in a convenient place for easy reference. · If you give the sewing machine to someone else, also give
them this instruction manual.
Contents
Before use
· · · · · · · · Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 How to change the power plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Doing so could cause an injury.
Attention
Use a TOYOTA-exclusive bobbin.
3 12 4 5 6 7 8 9 10 11
1 2
Pull up the spool pin. Position the felt, the thread spool and the spool cap on to the spool pin. Note: A felt was originally put on to the spool pin.
Spool cap
Felt
3
Pull the thread from the thread spool. Support the thread on the sewing machine with one hand, using the other hand pass the thread around the thread guide as shown in the diagram.
14
4 5
Pass the thread end through the hole of the bobbin as shown. Hole Place the bobbin on to the thread winding spindle so the groove will meet the shaft projection.
Thread Groove
Thread winding spindle
Shaft projection
6 7
Hold the thread end and push the thread winding switch to the left and start winding. Pass the thread through the take-up lever.
Take-up-lever
8
Pass the thread through the right side needle guide. It should be resistant and difficult to pull.
Needle guide
9
Pass the thread through the needle eye from the front. Front
15cm
18
Sewing preparations
· Pulling up the lower thread
1
Hold the end of the thread, turn the handwheel towards yourself for one full turn, and stop when the needle is at its highest position.
Handwheel
Note: Always turn the handwheel towards yourself (in the direction of the arrow). Note: If the thread is tight the lower thread will not come out, so hold the thread loosely.
2
Pull up the upper thread and the loop of the lower thread will come out. Pull out this lower thread.
Upper thread
Lower thread
3
Align the upper thread and lower thread, and thread through the groove of the presser foot. Pull back about 15 cm.
15cm
19
Sewing preparations
· Application of each stitch pattern
Caution
Don't turn the pattern selection dial while operating the sewing machine. Turn the handwheel towards yourself to raise the needle in the highest position. Pattern selection dial
Buttonhole
Blind hem stitch
Zigzag Applique Overcasting
Scallop stitch
Straight stitch Sewing-seams Zipper insertion
Castle stitch
Thin fabric straight stitch
Decorative stitch Fagotting
Mending stitch Thin fabric overcasting
Decorative stitch Serpentine
20
Sewing preparations
· Changing the presser foot
Caution
Remove the power plug from the outlet when changing the presser foot. Not doing so could cause an injury.
Removal
1
Raise the presser foot lever.
2
Turn the handwheel towards yourself to raise the needle. Note: Never turn in the wrong direction.
Handwheel
Presser foot lever
3
Press the presser foot holder lever in the direction of the arrow to release the presser foot.
Presser foot holder lever
Presser foot
21
Installation
1
Position the presser foot pin directly below the groove in the presser foot holder. Presser foot holder
Groove
Presser foot pin
2
Lower the presser foot lever to secure the presser foot.
Presser foot lever
22
Sewing preparations
· Changing the needle
Caution
Remove the power plug from the outlet when changing the needle. Not doing so could cause an injury.
1 2
Turn the handwheel towards yourself to raise the end of the needle higher than the needle plate. Hold the needle in one hand, loosen the needle clamp screw with the screw driver for the needle plate, and remove the needle. Loosen the needle clamp screw to remove the needle.
Screw driver for the needle plate
Needle clamp screw
3
Face the flat surface of the needle to the rear and insert until it makes contact with the pin. Firmly tighten the needle clamp screw with the screw driver for the needle plate.
Flat surface
Pin
Correct needle selection
Good needle
If a faulty needle is used, not only could it impair the sewing performance, but it could also damage the needle plate or hook, or break the needle. Faulty needle
The entire needle is bent
The point of the needle is crushed / worn away
The point of the needle is bent 23
Sewing preparations
·
Relationship between the needle, thread and fabric, and adjusting the thread tension
The quality of the sewing finish will improve if the needle and thread are changed to match the type of fabric. Follow the directions in the table below.
Sewing thin fabric
Sewing normal fabric
Sewing thick fabric
No. [. . . ] Note: Use a light bulb with a maximum power of 15 W.
4
Always reinstall the face cover after replacing the light bulb.
41
Maintenance
· Troubleshooting
Trouble Does not rotate Does not work Loud noise Slow rotation Cause
What is the problem?Check the following possibilities before contacting the service center for repair.
Countermeasure Connect the power plug correctly Clean the hook Remove thread waste or dust Install the needle correctly Firmly tighten the screw Use a needle appropriate to the fabric Adjust the thread tension Do not pull the fabric strongly Put the bobbin case in the correct position Thread the upper and lower thread Remove thread waste from the feed dog and hook Adjust the thread tension Use a good needle Page 10 37 37 21 21 22 28 23 38 14, 15 37 28 21 14 37 18
The power plug is not inserted Thread is tangled in the hook, or there is a broken needle in the hook There is thread waste or dust in the hook or feed dog The needle is incorrectly installed The needle clamp screw is loose The needle is too fine for the cloth The tension of the upper thread is too tight The fabric is being pulled too strongly The bobbin case is not in the correct position The upper and lower thread are not correctly threaded The thread is tangled in the bobbin case or hook The tension of the upper thread is too tight The needle is bent The point of the needle is burred
Broken needle
Broken upper thread
Broken lower thread Fabric not fed through
The lower thread is incorrectly threaded There is thread waste in the feed dog The pattern selection dial is set to "2" or "4"
Thread the lower thread Remove thread waste from the feed dog and hook Set a correct pattern
42
Trouble
Cause The needle is incorrectly installed
Countermeasure Install the needle correctly Use a straight needle Sew with a needle and thread appropriate to the fabric Thread the upper thread correctly Adjust the thread tension Thread the upper and lower thread again Use a needle appropriate to the fabric Use a good needle Thread the lower thread again Adjust the thread tension Insert the bobbin in the bobbin case correctly Thread the upper thread correctly Adjust the thread tension
Page 21 21 22 15 28 14, 15 22 21 14 28 14 15 28
Missed stitches
The needle is bent The needle and thread are not appropriate for the fabric The upper thread is not correctly thread The tension of the upper thread is too tight
The fabric wrinkles / puckers
The upper and lower thread are not correctly thread The needle is too thick for the cloth The needle is burred The lower thread is incorrectly threaded The tension of the upper thread is too tight The bobbin is not correctly inserted in the bobbin case The upper thread is not correctly threaded
Too much lower thread showing on right side of the fabric
Too much upper thread showing on wrong side of the fabric
The tension of the upper thread is too loose The upper thread is not correctly threaded (not threaded through the thread guide)
Thread the upper thread correctly
15
If the above treatments do not solve the problem, contact the service center as described in your warranty. When calling for service, please note the MODEL and SERIES that are inscribed on the back of your sewing machine.
SP10 SERIES / SERIE MODEL / MODELE
Manufacturer/ : ZHEJIANG AISIN ELITE Fabricant MACHINERY & ELECTRIC CO. , LTD. P. R. C.
220-240V
Total 85W
50Hz
max 15W
Importer/ : Importateur
EUROPE S. / FABRIQUE A P. R. C.
43
Maintenance / Others
·
Servicing double-insulated products (230V-240V)
In a double-insulated product, two systems of insulation are provided instead of grounding. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TOYOTA SPA15
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual TOYOTA SPA15 will begin.