User manual TYAN THUNDER N4250QE

[. . . ] Thunder n4250QE /// Version 1. 00 S4985G3NR Copyright Copyright © TYAN Computer Corporation, 2006. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. AMD, Opteron, and combinations thereof are trademarks of AMD Corporation. Phoenix, Phoenix-AwardBIOS are trademarks of Phoenix Technologies. Notice Information contained in this document is furnished by TYAN Computer Corporation and has been reviewed for accuracy and reliability prior to printing. [. . . ] Disabled / 360kb 5 1/4" / 1. 2MB 5 1/4" / 720kb 3 1/2" / 2. 88MB 3 1/2" 53 3. 3. 7 I/O Device Configuration This setting allows you to configure I/O devices. PhoenixBIOS Setup Utility Advanced Memory Security Boot Power Exit I/O Device Configuration Item Specific Help [Enabled] [3F8] [IRQ4] [Enabled] [Normal] [2F8] [IRQ3] [Auto] [ECP] [Enabled] [Primary] Main Serial port A: Base I/O address: Interrupt: Serial port B: Mode: Base I/O address Interrupt: Parallel port: Mode: Floppy Disk Controller: Base I/O address: F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values Serial Port A This defines how the serial port is detected and configured. Enabled / Disabled / Auto Base I/O Address This sets the base I/O address for serial port A. 3F8 / 2F8 / 3E8 / 2E8 Interrupt This sets the interrupt for serial port A. IRQ4 / IRQ3 Serial Port B This defines how the serial port is detected and configured. Enabled / Disabled / Auto Mode This feature is used to set the mode for serial port B. Normal / IR / ASK-IR 54 Base I/O Address This sets the base I/O address for serial port B. 2F8 / 3F8 / 3E8 / 2E8 Interrupt This sets the interrupt for serial port B. IRQ3 / IRQ4 Parallel port: This defines how the parallel port is detected and configured. Auto / Disable / Enabled Mode This feature is used to set the mode for parallel port. ECP / Output Only / Bi-directional / EPP Floppy Disk Controller This defines how the floppy disk controller is detected and configured. Enabled/ Disabled / Auto Base I/O Address This sets the base I/O address for floppy disk controller. Primary / Secondary 55 3. 3. 8 Hardware Monitor This displays critical system parameters like CPU speed, fan speeds, voltage levels and CPU temperature. PhoenixBIOS Setup Utility Memory Security Boot Power Exit Hardwar Monitor Item Specific Help Main Advanced CPU0 Temperature CPU1 Temperature CPU2 Temperature CPU3 Temperature Sys1 Temperature Sys2 Temperature Sys3 Temperature Sys4 Temperature Sys5 Temperature CPU0 Fan Speed CPU1 Fan Speed CPU2 Fan Speed CPU3 Fan Speed System Fan0 Speed System Fan1 Speed System Fan2 Speed System Fan3 Speed System Fan4 Speed System Fan5 Speed System Fan6 Speed System Fan7 Speed CPU0 VDD voltage CPU1 VDD voltage +12V +5V HT1. 2V 3. 3VSB CK804 Vcore 1. 5V F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values 56 3. 3. 9 Console Redirection Main PhoenixBIOS Setup Utility Advanced Memory Security Boot Power Exit Console Redirection Item Specific Help [Disabled] [19. 2K] [PC ANSI] [CTS/RTS] [Direct] [Off] Com Port Address Baud Rate Console Type Flow Control Console connection: Continue C. R. after POST: F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values Com Port Address If enabled it will use a port on the motherboard. Disabled / On-board COM A / On-board COM B Baud Rate This feature is used to enable the specified baud rate. 300 / 19. 2K / 1200 / 2400 / 9600 / 38. 4K / 57. 6K / 115. 2K Console Type This feature is used to enable the specified console type. VT100 / VT100. 8bit / PC-ANSI, 7bit / PC ANSI / VT100+ / VT-UTF8 Flow Control This feature is used to enable the flow control. None / XON/XOFF / CTS/RTS Console Connection This feature is used to indicate whether the console is connected directly to the system or a modem is used to connect. after POST This feature is used to enable console redirection after OS has loaded. Off / On 57 3. 3. 10 Watchdog Timer option Main PhoenixBIOS Setup Utility Advanced Memory Security Boot Power Exit Watchdog Timer option Item Specific Help [Disabled] [1] Watchdog Timer Timer_out Minutes F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values Watchdog Timer This feature is used to enable the watchdog timer function. Disabled / Enabled Timer_out Minutes This feature is used to set the watchdog timer. 1-255 Minutes 58 3. 4 Memory This setting allows you to tweak the various cache settings for optimal performance of your system. Press Enter to display the various cache settings. PhoenixBIOS Setup Utility Memory Security Boot Main Advanced Power Exit Cache Ram System Memory: Extended Memory: Memory Cache: Cache Video BIOS area: Cache Base 0-512K: Cache Base 512K-640K: Cache Extended Memory Area: Cache A000 ­ AFFF: Cache B000 ­ BFFF: Cache C800 ­ CBFF: Cache CC00 ­ CFFF: Cache D000 ­ D3FF: Cache D400 ­ D7FF: Cache D800 ­ DBFF: Cache DC00 ­ DFFF: Cache E000 ­ E3FF: Cache E400 ­ E7FF: Cache E800 ­ EBFF: Cache EC00 ­ EFFF: Item Specific Help [xxxx KB] [xxxx KB] [Enabled] [Write Back] [Write Back] [Write Back] [Write Back] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Write Back] [Write Protect] [Write Protect] [Write Protect] [Write Protect] F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values Memory Cacahe This feature is used to set the state of memory cache. [. . . ] Striping: see RAID 80 UltraDMA-33/66/100: a fast version of the old DMA channel. Without proper UltraDMA controller, your system cannot take advantage of higher data transfer rates of the new UltraDMA/UltraATA hard drives. This one port type can function as a serial, parallel, mouse, keyboard or joystick port. It is fast enough to support video transfer, and is capable of supporting up to 127 daisy-chained peripheral devices. [. . . ]