User manual TYAN TIGER I7501S

[. . . ] Tiger i7501S /// Revision 1. 00 S2725 Copyright © TYAN Computer Corporation, 2002. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. Intel, Xeon, and combinations thereof are trademarks of Intel Corporation. [. . . ] These settings enable DMA channel 0 and 1 to be enabled or disabled. 3. 11 ­ Chipset Options related to the chipset can be altered through the following. CPU Configuration North Bridge ICH5 South Bridge Intel PCI-64 Hub 2 All settings discussed in following sections. 34 http://www. TYAN. com 3. 12 ­ CPU Configuration Options related to the CPU chipset settings can be altered through the following. This setting allows you to take advantage of Hyper-Threading enabled Xeon processors. Enabling Hyper-Threading allows a compatible Xeon processor to process applications that are written for a multi-processor system even if you are using only one Xeon processor. Hyper-Threading Enable 3. 13 Chipset Configuration Please leave all options in this section at their default setting because they are crucial to the stability of the system. Spread Spectrum Disabled/ Enabled CAS Latency Auto / 2, 2. 5 ICH5 Validat e CPU Bist ICH Delayed transaction ICH DCB Enable MPS revision Enabled/ Disabled Enabled/ Disabled Enabled/ Disabled 1. 4/1. 1 3. 14 ­ Intel PCI-64 Hub 2 Chipset Configuration Options related to the Intel PCI-64 hub and its settings can be altered through the following. PCI bus frequency I/O Port Decode RAS Sticky Error Handling IOAPIC Support in MP Table VGA Decode 33, 66, 100, 133, Auto This option allows you to adjust the decode size of the I/O ports. This option allows you to define how RAS errors are handled and whether they are corrected or left as is. This option allows you to adjust settings for IOAPIC functions that relate to multi-processor handling. Please leave this option at its default setting. 3. 15 ­ ACPI Options related to power management settings can be altered through the following options. ACPI Aware O/S ACPI Advanced Yes No Defines whether the OS can manage IRQs, DMAs, and other system settings on its own. All settings discussed in following sections 35 http://www. TYAN. com 3. 16 ­ ACPI Advanced Options related to advanced power management settings interface can be altered through the following options. ACPI APIC Support BIOS à AML ACPI Stable Headless Mode After Power Fail Power button instant off Watchdog Timer WOL S1 & S5 Enable Disable Previous State Enabled Disabled Enable Disable Enabled Disabled Allows system to reboot after a power failure. Do not enable unless you are familiar with this feature Enables Wake On Lan support. (Only on 82551 NIC. ) This option allows you to define whether or not to enable ACPI management features. This setting toggles BIOS control of ACPI power features. 3. 17 ­ Boot Options related to boot dev ices can be altered through the following. These can be 2nd Boot Device customized depending on your 3rd Boot Device preference. Please refer to your SCSI card's documentation. Boot Device Priority Hard Disk Drives Removable Devices ATAPI CDROM Drives Interrupt 19 Capture 3. 18 ­ Security Options related system security can be altered through the following. Change Supervisor Password Change User Password Clear User Password Boot Sector Virus Protection Changes system password. Enabled Toggles protection of boot sector on the hard drive Disabled from being modified. 3. 19 ­ Exit Options related exiting and saving can be done using the following. Exit Saving Changes Exist Discarding Changes Load Setup Defaults Discard Changes Save Changes Exit and save options. Save changes. 36 http://www. TYAN. com Chapter 4: Diagnostics 4. 1 ­ Hardware Monitor Information ICH5 SMBus base address = EC80h Winbond83782D hardware Monitor Information Hardware Monitor Chip 1: Slave Address: Chip Clock: Winbond83782D 0x29h 14. 318MHz Sensor Name Bank 0 0 0 0 0 0 5 0 1 2 Register 0x28h 0x29h 0x2Ah 0x22h 0x23h 0x24h 0x51h 0x27h 0x50h 0x50h Other controlled by PWM1 controlled by PWM3 controlled by PWM4 R1 = 28K, R2 = 10K 2N3904 diode PII compatible diode PII compatible diode CPU1 Fan CPU2 Fan Chassis Fan 3 System Volt 3. 3V System Volt 5V System Volt 12V Battery Voltage System(VRM) temp CPU1 533FSB temp CPU2 533FSB temp W83627HF Super IO hardware Monitor Information Hardware Monitor Chip 2: Slave Address: Chip Clock: Sensor Name Chassis Fan 4 Chassis Fan 5 Chassis Fan 6 Bank 0 0 0 WinbondW83627HF (Super IO) 0x2ah 48. 000MHz Register 0x28h 0x29h 0x2Ah On chip Xeon Thermal Sensor for 400Mhz FSB Xeon Hardware Monitor Chip 3: Slave Address: Sensor Name CPU1 temperature Bank 0 Intel Xeon Thermal Sensor 0x18h Register 0x01h 37 http://www. TYAN. com On chip Xeon Thermal Sensor for 400Mhz FSB Xeon Hardware Monitor Chip 4: Slave Address: Intel Xeon Thermal Sensor 0x19h Sensor Name CPU2 temperature Bank 0 Register 0x01h Programming CPU thermal sensors for custom Hardware Monitoring requirements (the GPIO pins are on ICH5) GPIO27 X 1 0 1 0 GPIO28 X 1 1 0 0 CHANNEL# X 3 2 1 0 DEVICES Winbond 83782D (Always on) DIMM SPD (6 devices), and CK408B clock chip CPU1 and CPU2 Thermal sensor, Super IO W83627HF Reserved Reserved Note: if you experience problems with setting up your system, always check the following things in the following order: Memory, Video, CPU By checking these items, you will most likely find out what the problem might have been when setting up your system. For more information on troubleshooting, check the Tyan website at: http://www. tyan. com. 38 http://www. TYAN. com 4. 2 Beep Codes Fatal errors, which halt the boot process, are communicated through a series of audible beeps. [. . . ] BMC is a standalone mini-CPU and runs on its own Real Time Operating System (RTOS) to complete all different kinds of tasks. Backed by QLogic's ARM7 technology, IT manager can rest assure his server machines are always taken care. Unlike regular peripheral card such as AGP card, Network card or SCSI card, SMDC does not require any hardware specific driver. As long as a standby power comes into the system, SMDC will begin looking after the system. [. . . ]