User manual TYAN TIGER K8W

[. . . ] Tiger K8W /// Revision 1. 02 S2875 Copyright © TYAN Computer Corporation, 2001-2003. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. AMD, Opteron, and combinations thereof are trademarks of AMD Corporation. Linux is a trademark of Linus Torvalds IBM, PC, AT, and PS/2 are trademarks of IBM Corporation. [. . . ] This is the default setting and should not be changed unless the VGA card manufacturer requires Palette Snooping to be Enabled. ENABLED: BIOS uses PCI bus mastering for reading / writing to IDE drives. Allows user to reserve a specific IRQ for a legacy device (Note: most hardware devices & OS used do not support manual assigned). Allows user to reserve a specific DMA for a legacy device. Yes Plug & Play OS No PCI Latency Timer Allocate IRQ to PCI VGA 32 64 96 128 160 192 224 248 Yes No Disabled Palette Snooping Enabled PCI IDE Bus Master Disabled Enabled Available IRQ3 ~ IRQ15 Reserved DMA0 ~ 7 Available Reserved 49 http://www. TYAN. com 3. 06 ­ BIOS Boot Settings Menu You can display Boot Setup option by highlighting it using the Arrow ( / ) keys and pressing Enter. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit Boot Settings Boot Settings Configuration Boot Device Priority Removable Drives ¡ö Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. Select Screen Select Item +/- Change Option Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit ¡ôõ ¡÷ 3. 06. 1 ­ Boot Settings Configuration Sub-Menu Use this screen to select options for the Boot Settings Configuration. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit Boot Settings Configuration Quick Boot Quiet Boot Add On ROM Display Mode Boot up Number-Lock PS/2 Mouse Support Typematic Rate Keyboard Error Report Boot To OS/2 Wait for `F1' If Error Hit `DEL' Message Display Interrupt 19 Capture [Enabled] [Disabled] [Force BIOS] [On] [Enabled] [Fast] [Disabled] [No] [Enabled] [Enabled] [Disabled] ¡ö ¡ôõ Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. Select Screen Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit ¡÷ 50 http://www. TYAN. com Feature Boot Settings Configuration Quick Boot Mode Quiet Boot Add On ROM Display Mode Boot up Number-Lock PS/2 Mouse Support Typematic Rate Keyboard Error Report Boot To OS/2 Wait for `F1' If Error Option Description Enabled Disabled Disabled Enabled Force BIOS Keep Current On Off Enabled Disabled Fast Slow Disabled Enabled No Yes Enabled Disabled This option allows user bypass BIOS self test during POST. Allows user to force BIOS/Option ROM of add on cards to be displayed during quiet boot. Allows user to disable the "Press F1 to Continue" error message when error is detected. Allows user to disable the "Press DEL to enter setup" message during POST. Allows devices (such as network card) to capture INT19 for booting. Hit `DEL' Message Display Enabled Disabled Interrupt 19 Capture Disabled Enabled 51 http://www. TYAN. com 3. 06. 2 ­ Boot Device Priority Sub-Menu Use this screen to select options for the Boot Device Priority. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit Boot Device Priority 1st Boot Device [1st FLOPPY DRIVE] Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. Select Screen Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit ¡ôõ ¡ö ¡÷ Feature Boot Device Priority 1st Boot Device Option Description Settings for boot priority. These can be customized depending on your preference. 1st FLOPPY DRIVE Disabled 52 http://www. TYAN. com 3. 06. 3 ­ Removable Drives Sub-Menu Use this screen to select options for the Removable Drives. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit Removable Drives 1st Device [1st FLOPPY DRIVE] Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. ¡ö ¡ôõ Select Screen Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit ¡÷ Feature Removable Drives 1st Device Option 1st FLOPPY DRIVE Disabled Description Specifies the boot sequence for removable drive booting. This option will show all removable devices. 53 http://www. TYAN. com 3. 07 ­ BIOS Security Menu The system can be configured so that all users must enter a password every time the system boots or when BIOS Setup is entered, using either the Supervisor password or User password. The Supervisor and User passwords activate two different levels of password security. [. . . ] Standby mode: in this mode, the video and hard drives shut down; all other devices continue to operate normally. 67 http://www. TYAN. com UltraDMA-33/66/100: a fast version of the old DMA channel. Without a proper UltraDMA controller, your system cannot take advantage of higher data transfer rates of the new UltraDMA/UltraATA hard drives. This one port type can function as a serial, parallel, mouse, keyboard or joystick port. It is fast enough to support video transfer, and is capable of supporting up to 127 daisy-chained peripheral devices. [. . . ]