User manual TYAN TIGER K8WE

[. . . ] Tiger K8WE /// Version 1. 02 S2877 Copyright Copyright © TYAN Computer Corporation, 2005-2006. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Taro and Tiger K8WE are trademarks of TYAN Computer Corporation. AMD, Opteron, and combinations thereof are trademarks of AMD Corporation. [. . . ] Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced IRQ3 [Available] Item Specific Help 49 http://www. tyan. com IRQ4 IRQ5: IRQ7 IRQ9 IRQ10 IRQ11 IRQ15 Indicates a DMA, interrupt, I/O, or memory resource conflict with another device. [Available] [Available] [Available] [Available] [Available] [Available] F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature IRQ3/4/5/7/9/10/11/15 Option Available Reserved Description Reserves the specified IRQ for use by legacy ISA devices. 3. 6. 4 - IDE Configuration Sub-Menu You can use this screen to select options for the IDE Configuration settings. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Large Disk Access Mode: SMART Device Monitoring: Local Bus IDE adapter: Primary Master Primary Slave Secondary Master Secondary Slave [DOS] [Disabled] [Both] [None] [None] [None] [None] Item Specific Help Indicates a DMA, interrupt, I/O, or memory resource conflict with another device. 50 http://www. tyan. com F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Large Disk Access Mode SMART Device Monitoring Local Bus IDE adapter Option Other DOS Disabled Enabled Both Disabled Primary Secondary Menu Item Menu Item Description Select the IDE access mode. Configure the IDE channel. Primary Master/Slave Secondary Master/Slave Primary Master/Slave, Secondary Master/Slave The following screen shows the information of IDE device. PhoenixBIOS Setup Utility Advanced Item Specific Help Multi-Sector Transfers: LBA Mode Control: 32 Bit I/O: Transfer Mode: Ultra DMA Mode: [Disabled] [Disabled] [Disabled] [Standard] [Disabled] F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Multi-Sector Transfers Option Disabled Enabled 51 Description Specify the number of sectors per block for multiple sector transfer. http://www. tyan. com Disabled LBA Mode Control Enabled 32 Bit I/O Disabled Enabled Standard Fast PIO 1 Disabled Ultra DMA Mode Enabled Transfer Mode Enabling LBA causes Logical Block Addressing to be used in place of Cylinders, Heads_Sectors. Select the Ultra DMA mode used for moving data to/from the drive. 3. 6. 5 - Floppy Configuration Sub-Menu You can use this screen to select options for the Floppy Configuration settings. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Legacy Diskette A: Legacy Diskette B: Indicates a DMA, interrupt, I/O, or memory resource conflict with another device. [1. 44/1. 25MB 3 1/2"] [Disabled] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Legacy Diskette A/B Option Disabled Enabled Description Select floppy type 52 http://www. tyan. com 3. 6. 6 - I/O Device Configuration Sub-Menu You can use this screen to select options for the I/O Device Configuration settings. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Serial port A: Serial port B: Mode: Parallel port: Mode: Floppy disk controller: Base I/O address [Auto] [Auto] [Normal] [Auto] [ECP] [Enabled] [Primary] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Serial port A Serial port B Mode Parallel port Mode Floppy disk controller Base I/O address Option Disabled Enabled Disabled Enabled Normal IR Disabled Enabled Output only Bi-directional Disabled Enabled Primary Secondary Description Configure serial port A using options. Set the base I/O address for parallel port. 53 http://www. tyan. com 3. 6. 7- Hardware Monitor Sub-Menu You can use this screen to hardware monitor information. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced CPUx Temperature CPUx Fan Speed System Fan Speed CPUx VDD Voltage +12V +5v +3. 3V VLDT xxC xxxxRPM xxxxRPM x. x V x. xV x. xV x. xV x. xV Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values 3. 6. 8 ­ Console Redirection Sub-Menu You can use this screen to select options for the Console Redirection settings. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Com Port Address Baud Rate Console Type Flow Control Console connection Continue C. R. after POST [Disabled] [19. 2K] [VT100] [CTR/RTS] [Direct] [off] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values 54 http://www. tyan. com Feature Com Port Address Baud Rate Console Type Flow Control Option Disabled On-board COMA On-board COMB 19200 38400 57600 115200 VT100 VT100, 8bit PC-ANSI, 7bit PC ANSI VT100+ VT-UTF8 None XON/XOFF Direct Description Select the Com Port address. Enable the specified baud rate. Enable the specified console type. Enable flow control. Indicate whether the console is connected directly to the system or a modem is used to connect. Enable Console Redirection after OS has loaded. Console connection Via modem Continue C. R. after POST Off On 55 http://www. tyan. com 3. 6. 9­ Watchdog Timer Option Sub-Menu You can use this screen to select options for the Watchdog settings. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Watchdog Timer Time_Out Minutes [Disabled] [ 1] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Watchdog Timer Time_Out Minutes Option Disabled Enabled 1~255 Description Enable/disable Watchdog Timer Watchdog Time_Out configuration in Minutes(1255) 3. 7 - BIOS Memory Menu This menu has options for memory speed & latency. Use the <Plus> and <Minus> keys to change the value of the selected option. 56 http://www. tyan. com PhoenixBIOS Setup Utility Memory Cache Ram [XXXX KB] [Enabled] [uncached] [uncached] [uncached] [uncached] [uncached] [uncached] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] Item Specific Help Memory Cache: Cache System BIOS area: Cache Video BIOS area: Cache Base 0-512k: Cache Base 512k-640k: Cache Extended Memory Area: Cache A000 ­ AFFF: Cache B000 ­ BFFF Cache C800 ­ CBFF: Cache CC00 ­ CFFF: Cache D000 ­ D3FF: Cache D400 ­ D7FF: Cache D800 ­ DBFF: Cache DC00 ­ DFFF: Cache E000 ­ E3FF: Cache E400 ­ E7FF: Cache E800 ­ E8FF: Cache EC00 ­ EFFF: F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Memory Cache Cache A000-AFFF Cache B000-BFFF Cache C800-CBFF ~ Cache EC00-EFFF Option Disabled Enabled Disabled USHC Write Through Write Protect Write Back Disabled Write Through Write Protect Write Back Description Set the state of memory cache. Control caching of the memory blocks. Control caching of the memory blocks. 57 http://www. tyan. com 3. 8 - Security Menu This menu has options for the Security options. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Boot Supervisor Password Is: User Password Is: Set Supervisor Password Set User Password Fixed disk boot sector: Diskette access: Virus check reminder: System backup reminder: [Normal] [User] [Disabled] [Disabled] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Fixed disk boot sector Diskette access Option Normal Write Protect User Supervisor Disabled Virus check reminder Daily Disabled System back reminder Daily Description Write protects boot sector on hard disk to protect against viruses. Display reminder message at boot (daily, every Monday or 1st of every month). Display reminder message at boot (daily, every Monday or 1st of every month). 58 http://www. tyan. com 3. 9 - BIOS Boot Menu This menu has options for the Boot Device Priority. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Boot QuickBoot Mode: Boot-time Diagnostic Screen Summary screen POST Errors Default Primary Video Adapter Boot Device Priority [Disabled] [Disabled] [Disabled] [Enabled] [Add on] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature QuickBoot Mode Boot-time Diagnostic Screen Summary screen Option Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled POST Errors Boot Device Priority Default Primary Video Adapter Enabled Add on Onboard Description Allow the system to skip certain tests while booting. Pauses and displays SETUP entry or resume boot prompt if error occurs on boot if disabled, system always attempts to boot. [. . . ] Standby mode: in this mode, the video and hard drives shut down; all other devices continue to operate normally. Without a proper UltraDMA controller, your system cannot take advantage of higher data transfer rates of the new UltraDMA/UltraATA hard drives. This one port type can function as a serial, parallel, mouse, keyboard or joystick port. It is fast enough to support video transfer, and is capable of supporting up to 127 daisy-chained peripheral devices. [. . . ]