User manual TYAN TOLEDO I3200R S5211-1U

[. . . ] TYAN assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TYAN products including liability or warranties relating to fitness for a particular purpose or merchantability. TYAN retains the right to make changes to product descriptions and/or specifications at any time, without notice. In no event will TYAN be held liable for any direct or indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting from errors or inaccuracies of information contained in this document. 1 http://www. tyan. com Table of Contents Check the box contents!Chapter 1: Introduction 1. 1 Congratulations 1. 2 Hardware Specifications Chapter 2: Board Installation 2. 1 Board Image 2. 2 Block Diagram 2. 3 Board Parts, Jumpers and Connectors 2. 4 Tips on Installing Motherboard in Chassis 2. 5 Installing the Memory 2. 6 Installing the Processor and Cooling Fan 2. 7 Attaching Drive Cables 2. 8 Installing Add-in Cards 2. 9 Installing Optional SO-DIMM Modules 2. 10 Connecting External Devices 2. 11 Installing the Power Supply 2. 12 Finishing Up Chapter 3: BIOS Setup 3. 1 About the BIOS 3. 2 Main BIOS Setup 3. 3 Main Menu 3. 4 Advanced Menu 3. 5 Security Menu 3. 6 Power Menu 3. 7 Boot Menu 3. 8 Exit Menu Chapter 4: Diagnostics 4. 1 Beep Codes 4. 2 Flash Utility 4. 3 BIOS Post Code Appendix I: SMDC Information Appendix II: How to Make a Driver Diskette Glossary Technical Support 3 5 5 8 9 10 20 21 23 26 28 29 30 31 32 33 35 36 42 57 59 60 61 63 63 64 65 69 71 79 2 http://www. tyan. com Check the box contents! 1x S5191 motherboard 1x 34-Pin floppy drive cable 1 x Ultra-DMA-133/100/66/33 IDE cable 2 x Serial ATA power cables 4 x Serial ATA cables 1 x USB2. 0 cable 1 x S5191 user's manual 1 x S5191 Quick Reference guide 1 x TYAN driver CD 1 x I/O shield 1 x Serial & Parallel Port cable set If any of these items are missing, please contact your vendor/dealer for replacement before continuing with the installation process. [. . . ] Options: Disabled / Enabled Hyperthreading Enable this only if you have an Intel Hyper Threading processor. Hyper-Threading Technology enables multi-threaded software applications to execute threads in parallel. Hyper-Threading Technology provides thread-levelparallelism (TLP) on each processor resulting in increased utilization of processor execution resources. As a result, resource utilization yields higher processing throughput. Hyper-Threading Technology is a form of simultaneous multi-threading technology (SMT) where multiple threads of software applications can be run simultaneously on one processor. This is achieved by duplicating the architectural state on each processor, while sharing one set of processor execution resources. Hyper-Threading Technology also delivers faster response times for multi-tasking workload environments. By allowing the processor to use on-die resources that would otherwise have been idle, Hyper-Threading Technology provides a performance boost on multi-threading and multi-tasking operations for the Intel NetBurst® microarchitecture. Options: Enabled / Disabled Thermal Management 2 Select between TM1 and TM2. Options: Disabled / Enabled Numbers of Stop Grant This feature is used to configure the numbers of Stop Grant. Options: Per Core / Single 49 http://www. tyan. com Set Max Ext CPUID = 3 Sets Max CPUID extended function value to 3. Options: 378 / 278 / 3BC Interrupt: Set the interrupt for parallel port. Options: IRQ7 / IRQ5 Floppy Disk Controller: This defines how the floppy disk controller is detected and configured. Options: Disabled / Enabled / Auto 52 http://www. tyan. com 3. 4. 4 Hardware Monitoring This section allows you to fine tune the Hardware Monitoring configuration. Main PhoenixBIOS Setup Utility Advanced Security Power Hardware Monitoring Boot Exit Item Specific Help Voltage Monitoring Sub-Menu FAN Control Sub-Menu CPU FAN FAN1 FAN2 FAN3 FAN4 FAN5 CPU Temp. = Ambient Temp. =[ F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu 2250 RPM No Fan Input No Fan Input No Fan Input No Fan Input No Fan Input 56OC/132OF 37OC/98OF -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values All items on this submenu can not be modified in user mode. Read only. 3. 4. 4. 1 Voltage Monitoring Sub-Menu Main VDIMM= Vccp= Vcc= +5V= +12V= +3. 3Vsb= VBAT= PhoenixBIOS Setup Utility Advanced Security Power Voltage Monitoring Sub-Menu Xxxx Xxxx Xxxx Xxxx Xxxx Xxxx Xxxx V V V V V V V Boot Exit Item Specific Help All items on this menu can not be modified in user mode. If any items require changes, please consult your system supervisor. F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu -/+ Change Values Sub-Menu Enter Select F9 Setup Defaults F10 Previous Values All items on this submenu can not be modified in user mode. Read only. 53 http://www. tyan. com 3. 4. 4. 2 FAN Control Sub-Menu Main PhoenixBIOS Setup Utility Advanced Security Power FAN Control Sub-Menu [Disabled] [4 Pin] [4 Pin] [4 Pin] [4 Pin] Boot Exit Item Specific Help Auto Mode Fan Control Parameters Auto Fan Control CPU FAN Input type select FAN1 Input type select FAN2 Input type select FAN3 Input type select F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu -/+ Change Values Sub-Menu Enter Select F9 Setup Defaults F10 Previous Values Auto Fan Control: This feature is used to set function of Auto Mode Fan Control. Options: Enabled / Disabled CPU FAN / FAN1 / FAN2 / FAN3 Input Type Select: These features are used to select 3 or 4 pin fan connector. After the setting, then you can use the function of "Auto Fan Control". Options: 4 Pin / 3 Pin 54 http://www. tyan. com 3. 4. 5 DMI Event Logging This section allows you to fine tune the DMI Event Logging configuration. Main PhoenixBIOS Setup Utility Advanced Security Power DMI Event Logging Valid Full [Enter] [Enabled] [Enter] [No] -/+ Change Values Sub-Menu Enter Select F9 Setup Defaults F10 Previous Values Boot Exit Item Specific Help View the contents of the DMI event log. Event Log Validity Event Log Capacity View DMI event log: Event Logging: Mark DMI events as read: Clear all DMI Event logs: F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu View DMI Event log Press [Enter] to view BIOS event log Event Logging When set to [Enabled], errors will be logged to BIOS event log. Options: Enabled / Disabled Mark DMI Events as Read Press [Enter] to mark DMI events as read. Clear all DMI Event logs When set to [Enabled], BIOS event log will be cleared. [. . . ] This one port type can function as a serial, parallel, mouse, keyboard or joystick port. It is fast enough to support video transfer, and is capable of supporting up to 127 daisy-chained peripheral devices. VGA (Video Graphics Array): the PC video display standard V-SYNC: controls the vertical scanning properties of the monitor. PCI card that allows a RAID card to use the onboard SCSI chip, thus lowering cost of RAID solution ZIF Socket (Zero Insertion Force socket): these sockets make it possible to insert CPUs without damaging the sensitive CPU pins. [. . . ]